The PARIS Forums: PARIS: Main » S/MUX (ADAT doublewire) question

Home » The PARIS Forums » PARIS: Main » S/MUX (ADAT doublewire) question

Show: Today's Messages :: Polls :: Message Navigator

S/MUX (ADAT doublewire) question [message #90803]

Sat, 29 September 2007 13:23

Messages: 1124
Registered: July 2005

Senior Member

I'm getting ready to wire in a fairly involved hardware
configuration........really???.......moi? . For you guys who use 88.2 a lot,
I have a question. I need to be able to switch sample rates between projects
while not having to physicaly repatch any gear. I'll be using a MADI PCI/ADI
648 but I'm sure the S/MUX would apply to an HDSP series card of any type..
When changing from a 44.1 KHz projects to a 88.2 KHz projects do the HDSP
I/O channels reconfigure as follows??:

ADAT I/O 1
channels 1 & 2 combine to create channel 1
channels 3 & 4 combine to create channel 2
channels 5 & 6 combine to create channel 3
channels 7 & 8 combine to create channel 4
ADAT 1/O 2
channels 9 & 10 combine to create channel 5
channels 11 & 12 combine to create channel 6
channels 13 & 14 combine to create channel 7
channels 15 & 16 combine to create channel 8

or is it.....

ADAT I/O 1
channels 1 & 3 combine to create channel 1
channels 2 & 4 combine to create channel 2
channels 5 & 7 combine to create channel 3
channels 6 & 8 combine to create channel 4
ADAT 1/O 2
channels 9 & 11 combine to create channel 5
channels 10 & 12 combine to create channel 6
channels 13 & 15 combine to create channel 7
channels 14 & 16 combine to create channel 8

or is it

ADAT I/O channels 1 & 2 combine with ADAT I/O 9 & 10 to create channel 1 & 2
ADAT I/O channels 3 & 4 combine with ADAT I/O 11 & 12 to create channel 3 &
4
ADAT I/O channels 5 & 6 combine with ADAT I/O 13 & 14 to create channel 5 &
6
ADAT I/O channels 7 & 8 combine with ADAT I/O 15 & 16 to create channel 7 &
8

I just need to know ahead of time before I jump into this. I'm going to be
having to do this install without any assistance and I don't want to spend a
whole day getting this wired in and then end up with a total cluster**** in
my signal routing.

Report message to a moderator

[Message index]

		S/MUX (ADAT doublewire) question By: DJ on Sat, 29 September 2007 13:23
		Re: S/MUX (ADAT doublewire) question By: Neil on Sat, 29 September 2007 13:55
		Re: S/MUX (ADAT doublewire) question By: DJ on Sat, 29 September 2007 13:57
		Re: S/MUX (ADAT doublewire) question By: Neil on Sat, 29 September 2007 14:29
		Re: S/MUX (ADAT doublewire) question By: Neil on Sat, 29 September 2007 16:14
		Re: S/MUX (ADAT doublewire) question By: Chris Ludwig on Sat, 29 September 2007 15:10
		Re: S/MUX (ADAT doublewire) question By: DJ on Sat, 29 September 2007 16:49
		Re: S/MUX (ADAT doublewire) question By: Nei on Sat, 29 September 2007 17:29
		Re: S/MUX (ADAT doublewire) question By: DJ on Sat, 29 September 2007 17:25
		Re: S/MUX (ADAT doublewire) question By: DJ on Sat, 29 September 2007 17:24
		Re: S/MUX (ADAT doublewire) question By: JeffH on Sat, 29 September 2007 22:13
		Re: S/MUX (ADAT doublewire) question By: JeffH on Sat, 29 September 2007 22:20
		Re: S/MUX (ADAT doublewire) question By: DJ on Sat, 29 September 2007 23:16
		Re: S/MUX (ADAT doublewire) question By: DJ on Sat, 29 September 2007 23:16
		Re: S/MUX (ADAT doublewire) question By: JeffH on Sun, 30 September 2007 20:30
		Re: S/MUX (ADAT doublewire) question By: DJ on Sun, 30 September 2007 22:18
		Re: S/MUX (ADAT doublewire) question By: JeffH on Mon, 01 October 2007 10:54
		Re: S/MUX (ADAT doublewire) question By: DJ on Sun, 30 September 2007 16:52

Previous Topic:	RME D/A converters
Next Topic:	Will Downing

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Sun Jun 09 14:10:08 PDT 2024

Total time taken to generate the page: 0.00788 seconds