The PARIS Forums


Home » The PARIS Forums » PARIS: Main » OT - Studio design question
OT - Studio design question [message #104224] Wed, 14 October 2009 21:49 Go to next message
pbraun is currently offline  pbraun   UNITED STATES
Messages: 63
Registered: June 2009
Location: Northwest Indiana
Member
While I'm in a question-asking mood....

Now that I've got the mixing bug again, it's time to put up some damn walls in this concrete box of a basement.

My little corner paradise will be about 12' wide by 17' deep, with roughly 7' ceiling clearance.

Since you have to put bass traps in the corners anyway, would it be smart to frame out the walls and then frame the corners at a small diagonal, essentially creating an octagon-shaped room? That would eliminate 90-degree corners, at least vertical ones.

I'm going to do this with alternating studs for inside and outside surfaces, glued to the walls and floors for extra isolation, two layers of drywall on both sides, dense rockwool in between. I live in a condo, and share one of the walls with our neighbor's basement, plus I share the ceiling with the CFO and I've learned it doesn't pay to piss her off on "Survivor" night.

Due to the cost of such a project, I'll probably be doing one wall at a time, but want to have the overall plan down before I start.

I've read at least a dozen articles on home studio construction, and they all say something different. And while I'd love to have layers of mass-loaded vinyl in between each layer of drywall, suspended on isolation channel, as of tonight we still haven't won Powerball so that ain't happening.



Paul Braun, Certified Music Junkie

"Music washes from the soul the dust of everyday life." -- Harlan Howard
Re: OT - Studio design question [message #104225 is a reply to message #104224] Wed, 14 October 2009 21:50 Go to previous messageGo to next message
pbraun is currently offline  pbraun   UNITED STATES
Messages: 63
Registered: June 2009
Location: Northwest Indiana
Member
And I forgot to add that this is a mixing room only. I have no room for recording -- all of my recording will either be done at a friend's studio, or with my mobile Paris rig.


Paul Braun, Certified Music Junkie

"Music washes from the soul the dust of everyday life." -- Harlan Howard
Re: OT - Studio design question [message #104227 is a reply to message #104225] Wed, 14 October 2009 23:37 Go to previous messageGo to next message
JeffH is currently offline  JeffH   UNITED STATES
Messages: 307
Registered: October 2007
Location: Wamic, OR
Senior Member
Paul,

Take a look at

http://www.realtraps.com/part_studio.htm

My new room is based on this config (Scaled to fit 17' as well). I am amazed at the difference the lack of parallel walls makes. Even with nothing in the room, the acoustics are pretty smooth before the absorbers.

Hopefully I'll actually get it up and running in the next couple months.

Jeff
Re: OT - Studio design question [message #104229 is a reply to message #104227] Thu, 15 October 2009 02:51 Go to previous messageGo to next message
dnafe is currently offline  dnafe   CANADA
Messages: 390
Registered: February 2009
Senior Member
No doubt you've probably been to these sites but just in case

http://www.johnlsayers.com/phpBB2/index.php

http://www.recording.org/forum-34.html

http://forum.studiotips.com/viewforum.php?f=35&sid=5774d d4ba12d1f1f6fe3bf306e097c80

Re: OT - Studio design question [message #104230 is a reply to message #104229] Thu, 15 October 2009 10:58 Go to previous messageGo to next message
pbraun is currently offline  pbraun   UNITED STATES
Messages: 63
Registered: June 2009
Location: Northwest Indiana
Member
OK, my head just exploded. Gimme a minute to clean the brain matter off my monitor.

(wiping, wiping, wiping....)

I'm back.

I may go with the trapezoidal room concept, but frame the outside square to make it look neater. Gotta go with double walls anyway, nothing says they have to be parallel.

No matter what, it will have to be "plan once, build piece-by-piece" as budget allows.

And who knows? Once I fix up the rest of the joint, I may set up a recording space in the other part of the basement. It would have to be musos I know and trust, 'cuz I'm not comfortable with strangers walking through my living room and seeing our art collection...



Paul Braun, Certified Music Junkie

"Music washes from the soul the dust of everyday life." -- Harlan Howard
Re: OT - Studio design question [message #104231 is a reply to message #104230] Thu, 15 October 2009 11:34 Go to previous messageGo to next message
kerryg is currently offline  kerryg   CANADA
Messages: 1529
Registered: February 2009
Senior Member
Administrator
You could see if it's feasible to do *just the ceiling* in this stuff. It's expensive compared to regular drywall (between $50 and $120 a sheet, although it's hard to pin it down) but if my math isn't completely out to lunch all you'd need is five 4x12 sheets to cover a (assuming "slightly less than" after framing) 12x17 ceiling.

If you could get that amount for a couple of hundred bucks (it installs like drywall so you'll save tons by installing it yourself) then for that pretty reasonable price the sound barrier between you and the CFO would be as good as it's realistically going to get in a residential space.

Roxul SafeNSound is excellent value for insulation, and it works great.


"... being bitter is like swallowing poison and waiting for the other guy to die..." - anon
Re: OT - Studio design question [message #104233 is a reply to message #104230] Thu, 15 October 2009 13:49 Go to previous messageGo to next message
JeffH is currently offline  JeffH   UNITED STATES
Messages: 307
Registered: October 2007
Location: Wamic, OR
Senior Member
Paul,

Mine is built out inside of an existing structure. I lucked out with side adjacent to the outside wall because building the trapezoid left a little crawl space. When I realized I needed a lightpipe from my machine area, there was a built in crawl space (albeit for a pretty small person).

Jeff
Re: OT - Studio design question [message #104333 is a reply to message #104233] Thu, 19 November 2009 12:06 Go to previous messageGo to next message
mylescdavis is currently offline  mylescdavis   FRANCE
Messages: 7
Registered: November 2009
Junior Member
Hi, Paul -

I'd suggest you try the simplest and cheapest approach first.

At your Home Depot (or local big box building supply equivalent), find some fiberglass or rockwool slabs 2 inches or 4 inches thick. 703 is the Owens Corning fiberglass variety; the Rockwool you want is approximately 45kg/m3 in density. It's named differently in different countries.

What you want to do is cut these panels (they're usually 2 x 4 feet, or 600 x 1200mm) so that you have the largest triangles you can make, or that you can tolerate in your room from a losing-floorspace point of view. Stack them up from floor to ceiling in two corners. If you like what happens (as you probably will), do the same in your other two corners. It will be great for mixing - you'll be surprised at the difference in what you hear (and don't) in the room.

You can also make wood frames for these panels and hang them on the walls, which is important to do at any reflective spots between you and your monitors.

A whole industry has grown out of making acoustic stuff to sell to people. 95% of it can be done yourself, pretty cheaply, with the same materials the manufacturers use. They're selling convenience, not better technology.

You can see these in my studio here: http://mylescochran.com/studiofrance.htm
Re: OT - Studio design question [message #104334 is a reply to message #104224] Fri, 20 November 2009 07:44 Go to previous messageGo to next message
mani1147 is currently offline  mani1147   CANADA
Messages: 130
Registered: May 2009
Location: NB Canada
Senior Member
Hi Paul, I have an octagon shape room and I like it but one thing I want to suggest that I missed when designing my setup is "A proper machine room/area" for all those loud equipment fans. If your still in the design phase, now's the time. If you already thought of it, cool. I went with an area in my desk for the computers and MECS but I would definitely take them out of the control room if I was to do it over. They aren't that loud but it would have been so easy to do back then.....Along with other things I suppose....oops, did I say that out loud!! Rolling Eyes

just my 2 cents, good luck
Rob_Aindex.php?t=getfile&id=672&private=0
  • Attachment: desk.jpg
    (Size: 101.25KB, Downloaded 362 times)

[Updated on: Fri, 20 November 2009 08:22]

Report message to a moderator

Re: OT - Studio design question [message #104336 is a reply to message #104334] Fri, 20 November 2009 13:54 Go to previous messageGo to next message
pbraun is currently offline  pbraun   UNITED STATES
Messages: 63
Registered: June 2009
Location: Northwest Indiana
Member
I kinda dig the trapezoidal LCD in the middle... Very Happy

I've planned on remoting the pcs already. I've got a square wire restaurant shelf about 6' high with three shelves - bottom one will hold the G5 and the APC 2500 UPS, middle shelf will hold the HP XW Twins, and I'll probably just lay the G4 with the Oasys card on it's side on the top shelf. All those cables will be routed through a passthrough stuffed with sound-deadening uhhhh....stuff.

I was toying with mounting the Oasys G4 in the rack with the MECs since I have a spare set of Marathon rackmounts, but then I realized that would put the fan/HD noise of the G4 in the studio instead of outside.

Actually, is there a reason to keep the MECs in the studio? Could they also be outside the room with snakes connecting them to a patch bay?

Since I'm building the walls from scratch, I'm still toying with a trapezoidal room. I'll definitely go with the DIY corner blockers and things that have been mentioned - cheaper is more gooder, in this case.



Paul Braun, Certified Music Junkie

"Music washes from the soul the dust of everyday life." -- Harlan Howard

[Updated on: Fri, 20 November 2009 13:56]

Report message to a moderator

Re: OT - Studio design question [message #104337 is a reply to message #104336] Fri, 20 November 2009 14:03 Go to previous messageGo to next message
mani1147 is currently offline  mani1147   CANADA
Messages: 130
Registered: May 2009
Location: NB Canada
Senior Member
So you like my " trapezoidal LCD " do ya......!!
Amazing, I paid 700 bucks a peice for those LCDs back in 03, times are a changin. My stich job definitely leaves something to be desired. Have to put that Canon wide angle lens on the xmas list.

As for your MECs, I would try to get them out of the ctrl room as well. With mine, one of em is whisper quiet but the other is quite loud, time for a new fan soon but I dread having to venture back there into the abyss of cables.

Rob_A

[Updated on: Fri, 20 November 2009 18:13]

Report message to a moderator

Re: OT - Studio design question [message #104338 is a reply to message #104337] Fri, 20 November 2009 19:58 Go to previous message
pbraun is currently offline  pbraun   UNITED STATES
Messages: 63
Registered: June 2009
Location: Northwest Indiana
Member
Well, that would solve the problem of where to put the Oasys G4. I can rack it under the MECs and leave them outside the room.

I would imagine that if I decided at some point to do any recording here, as long as I know they're calibrated properly, as long as my preamps don't go red then I don't have to worry about the blinky lights on front of the input cards.



Paul Braun, Certified Music Junkie

"Music washes from the soul the dust of everyday life." -- Harlan Howard
Previous Topic: Studio pics / images with Paris rigs
Next Topic: Invitation code to register for Paris Wiki?
Goto Forum:
  


Current Time: Sat Dec 28 06:15:33 PST 2024

Total time taken to generate the page: 0.02504 seconds