The PARIS Forums


Home » The PARIS Forums » PARIS: Main » Bounce to disk issue
Bounce to disk issue [message #97660] Mon, 31 March 2008 12:06 Go to next message
Bill T is currently offline  Bill T
Messages: 1
Registered: March 2008
Junior Member
Anybody else seen this prob with 3.0 on Windows XP? When doing a bounce to
disk, I get the dialog box asking for filename, but meanwhile the bounce
has already started and the tracks are playing.

I'd swear that it just started doing this, and for some reason, it seems
that the first time you do a bounce in a project it waits for the name before
beginning the bounce. As it is now, I just have to leave enough 'roll time'
ahead of the tracks to give me time to type in a filename. Not an ideal solution...

Any ideas?
Re: Bounce to disk issue [message #97661 is a reply to message #97660] Mon, 31 March 2008 12:46 Go to previous messageGo to next message
Wayne Carson is currently offline  Wayne Carson   UNITED STATES
Messages: 86
Registered: June 2007
Member
Hi Bill,

That's a new one. I just tried my system. Using the bounce to disc button
on the master mixer (12.) I started and stop'd mixdowns 3 times. Twice using
the C16 record/play buttons and once with the mouse on the on screen
transport (4.). Each time the system prompted me with "mixdown" and waited
until I clicked save or OK (I forget). Worked fine each time.

So, I'm no help.

Wayne



"Bill T" <nospan@nospam.com> wrote in message news:47f13623$1@linux...
>
> Anybody else seen this prob with 3.0 on Windows XP? When doing a bounce to
> disk, I get the dialog box asking for filename, but meanwhile the bounce
> has already started and the tracks are playing.
>
> I'd swear that it just started doing this, and for some reason, it seems
> that the first time you do a bounce in a project it waits for the name
> before
> beginning the bounce. As it is now, I just have to leave enough 'roll
> time'
> ahead of the tracks to give me time to type in a filename. Not an ideal
> solution...
>
> Any ideas?
Re: Bounce to disk issue [message #97662 is a reply to message #97660] Mon, 31 March 2008 13:51 Go to previous messageGo to next message
EK Sound is currently offline  EK Sound   CANADA
Messages: 939
Registered: June 2005
Senior Member
That happened because you pressed play first... hold record down THEN
press play... the dialog box will pop up first then the bounce will
start once the name is entered. Also, allow for at least 2 seconds of
dead air from where you have the now line set or you will clip off the
front of the bounce.

David.

Bill T wrote:
> Anybody else seen this prob with 3.0 on Windows XP? When doing a bounce to
> disk, I get the dialog box asking for filename, but meanwhile the bounce
> has already started and the tracks are playing.
>
> I'd swear that it just started doing this, and for some reason, it seems
> that the first time you do a bounce in a project it waits for the name before
> beginning the bounce. As it is now, I just have to leave enough 'roll time'
> ahead of the tracks to give me time to type in a filename. Not an ideal solution...
>
> Any ideas?
Re: Bounce to disk issue [message #97701 is a reply to message #97662] Tue, 01 April 2008 10:57 Go to previous messageGo to next message
Miguel Vigil [1] is currently offline  Miguel Vigil [1]
Messages: 258
Registered: July 2005
Senior Member
Nope... I tried that early on, and that doesn't work either. I found out that
clicking record in the transport window, rather than using the CS transport
controls works fine, so that's what I do now.

I guess it must be something in the CS interface, I dunno. Thanks for the
input never the less...
BT

EK Sound <ask_me@nospam.net> wrote:
>That happened because you pressed play first... hold record down THEN
>press play... the dialog box will pop up first then the bounce will
>start once the name is entered. Also, allow for at least 2 seconds of
>dead air from where you have the now line set or you will clip off the
>front of the bounce.
>
>David.
>
>Bill T wrote:
>> Anybody else seen this prob with 3.0 on Windows XP? When doing a bounce
to
>> disk, I get the dialog box asking for filename, but meanwhile the bounce
>> has already started and the tracks are playing.
>>
>> I'd swear that it just started doing this, and for some reason, it seems
>> that the first time you do a bounce in a project it waits for the name
before
>> beginning the bounce. As it is now, I just have to leave enough 'roll
time'
>> ahead of the tracks to give me time to type in a filename. Not an ideal
solution...
>>
>> Any ideas?
Re: Bounce to disk issue [message #97722 is a reply to message #97701] Wed, 02 April 2008 09:07 Go to previous messageGo to next message
Sandy Tipping is currently offline  Sandy Tipping   UNITED STATES
Messages: 54
Registered: June 2007
Member
This has happend randomly for as long as I've used Paris, and I'm using
WinME (since about 2000).

I do find that being very deliberate about record and then play (leaving at
least half a second between rec and play) solves this most of the time.

It seems to be at it's worst when I'm in a hurry to send a rough mix - stop,
select last recorded, delete files, start again.

S


"Bill T" <nospam@nospam.com> wrote in message news:47f27798$1@linux...
>
> Nope... I tried that early on, and that doesn't work either. I found out
> that
> clicking record in the transport window, rather than using the CS
> transport
> controls works fine, so that's what I do now.
>
> I guess it must be something in the CS interface, I dunno. Thanks for the
> input never the less...
> BT
>
> EK Sound <ask_me@nospam.net> wrote:
>>That happened because you pressed play first... hold record down THEN
>>press play... the dialog box will pop up first then the bounce will
>>start once the name is entered. Also, allow for at least 2 seconds of
>>dead air from where you have the now line set or you will clip off the
>>front of the bounce.
>>
>>David.
>>
>>Bill T wrote:
>>> Anybody else seen this prob with 3.0 on Windows XP? When doing a bounce
> to
>>> disk, I get the dialog box asking for filename, but meanwhile the bounce
>>> has already started and the tracks are playing.
>>>
>>> I'd swear that it just started doing this, and for some reason, it seems
>>> that the first time you do a bounce in a project it waits for the name
> before
>>> beginning the bounce. As it is now, I just have to leave enough 'roll
> time'
>>> ahead of the tracks to give me time to type in a filename. Not an ideal
> solution...
>>>
>>> Any ideas?
>
Re: Bounce to disk issue [message #97820 is a reply to message #97722] Mon, 07 April 2008 15:00 Go to previous message
Miguel Vigil [1] is currently offline  Miguel Vigil [1]
Messages: 258
Registered: July 2005
Senior Member
Glad(?) to hear it's not just my rig I guess. But I know the drill well; stop,
select last recorded files, delete.... I'll try the method you use and see
if it works.


"Sandy Tipping" <tippsand@earthling.net> wrote:
>This has happend randomly for as long as I've used Paris, and I'm using

>WinME (since about 2000).
>
>I do find that being very deliberate about record and then play (leaving
at
>least half a second between rec and play) solves this most of the time.
>
>It seems to be at it's worst when I'm in a hurry to send a rough mix - stop,

>select last recorded, delete files, start again.
>
>S
>
>
>"Bill T" <nospam@nospam.com> wrote in message news:47f27798$1@linux...
>>
>> Nope... I tried that early on, and that doesn't work either. I found out

>> that
>> clicking record in the transport window, rather than using the CS
>> transport
>> controls works fine, so that's what I do now.
>>
>> I guess it must be something in the CS interface, I dunno. Thanks for
the
>> input never the less...
>> BT
>>
>> EK Sound <ask_me@nospam.net> wrote:
>>>That happened because you pressed play first... hold record down THEN
>>>press play... the dialog box will pop up first then the bounce will
>>>start once the name is entered. Also, allow for at least 2 seconds of
>>>dead air from where you have the now line set or you will clip off the
>>>front of the bounce.
>>>
>>>David.
>>>
>>>Bill T wrote:
>>>> Anybody else seen this prob with 3.0 on Windows XP? When doing a bounce
>> to
>>>> disk, I get the dialog box asking for filename, but meanwhile the bounce
>>>> has already started and the tracks are playing.
>>>>
>>>> I'd swear that it just started doing this, and for some reason, it seems
>>>> that the first time you do a bounce in a project it waits for the name
>> before
>>>> beginning the bounce. As it is now, I just have to leave enough 'roll
>> time'
>>>> ahead of the tracks to give me time to type in a filename. Not an ideal
>> solution...
>>>>
>>>> Any ideas?
>>
>
>
Previous Topic: Is there a non-pace version of Paris 3.0 for XP?
Next Topic: Sleepwalk solo
Goto Forum:
  


Current Time: Fri Dec 06 07:56:28 PST 2024

Total time taken to generate the page: 0.01467 seconds