The PARIS Forums


Home » The PARIS Forums » PARIS: Projects » Clock Sync between 2 MECs (Clock Sync between 2 MECs)
Clock Sync between 2 MECs [message #106713] Thu, 03 November 2011 16:12 Go to next message
mvanbibber is currently offline  mvanbibber   UNITED STATES
Messages: 2
Registered: October 2011
Junior Member
I have ParisPro 3.0 with the driver I purchased for XP. When Paris pro loads the two MEC that I have they do not seem to be in sync. The A says internal 44hz and the second B says word 48hz. When I try to switch it in Paris from 44 to 48 it switches it on A only. Shouldn't they say the same thing? I have a BNC from A out to B in. I have the MECs plugged into two EDS1000 cards. Each MEC has 16 inputs and 8 out puts. I can switch B as the master switch the BNC around and get similar results. Thanks,Matt

Report message to a moderator

Re: Clock Sync between 2 MECs [message #106714 is a reply to message #106713] Fri, 04 November 2011 05:58 Go to previous messageGo to next message
dnafe is currently offline  dnafe   CANADA
Messages: 390
Registered: February 2009
Senior Member
By default both MECs run at 44.1K despite what the lights and A and B say

Caveat: this is from memory so I might be wrong but I have two MECs and see the same thing and have never had any issues.

That being said someone will no doubt chime in with a more authoritative answer for you

[Updated on: Fri, 04 November 2011 05:59]

Report message to a moderator

Re: Clock Sync between 2 MECs [message #106716 is a reply to message #106714] Sat, 05 November 2011 03:24 Go to previous messageGo to next message
thesandbox1 is currently offline  thesandbox1   GERMANY
Messages: 167
Registered: July 2009
Location: Carmel, IN
Senior Member
What is your clock source set to in the PARIS project? Internal?

https://www.facebook.com/Sandbox-Productions-Recording-Studi o-Carmel-IN-122733877784336/

Report message to a moderator

Re: Clock Sync between 2 MECs [message #106718 is a reply to message #106716] Sat, 05 November 2011 13:50 Go to previous messageGo to next message
mvanbibber is currently offline  mvanbibber   
Messages: 2
Registered: October 2011
Junior Member
The default clock source is internal 44 when the program loads. Although it is set to this and everything loads I see that mec A says internal 44 but mec B says word 48. I can change it to internal 48 and mec a switches but mec b stays at wprd 48. One would think that mec A and B would say the same thing. I was wondering what other peoples look like.
Thanks

Report message to a moderator

Re: Clock Sync between 2 MECs [message #106725 is a reply to message #106718] Fri, 11 November 2011 01:22 Go to previous message
kerryg is currently offline  kerryg   CANADA
Messages: 1529
Registered: February 2009
Senior Member
Administrator
The samplerate display on MEC B becomes irrelevant once A and B are sync'd: ie only MEC A's display means anything. As far as I can recall, it's always been that way.

"... being bitter is like swallowing poison and waiting for the other guy to die..." - anon

Report message to a moderator

Previous Topic: Scherzo beta 1.31
Next Topic: What is happening with win 7 drivers ?
Goto Forum:
  

[ Syndicate this forum (XML) ] [ RSS ] [ PDF ]

Current Time: Thu Nov 21 15:15:56 PST 2024

Total time taken to generate the page: 0.00887 seconds
.:: Contact :: Home ::.

Powered by: FUDforum 3.1.3.
Copyright ©2001-2023 FUDforum Bulletin Board Software