The PARIS Forums: PARIS: Main » external mixing/summing

Home » The PARIS Forums » PARIS: Main » external mixing/summing

Show: Today's Messages :: Polls :: Message Navigator

external mixing/summing [message #105384]

Fri, 02 July 2010 01:44

mono

Messages: 20
Registered: August 2006
Location: netherlands

Junior Member

Can i mix/sum my channels external in some paris config????

I don't need the gear, the gear needs me.

Report message to a moderator

Re: external mixing/summing [message #105385 is a reply to message #105384]

Fri, 02 July 2010 04:37

mono

Messages: 20
Registered: August 2006
Location: netherlands

Junior Member

I now got 2x eds1000 + 2xmec + 2x a8in
3x aut + if2.

I'd love to have a setup so i can record stuff on seperate tracks.
I'd love to hook up some external fx.
And rout the channels into a summing mixer i have.

I don't need the gear, the gear needs me.

Report message to a moderator

Re: external mixing/summing [message #105389 is a reply to message #105384]

Fri, 02 July 2010 07:46

ganttmann1

Messages: 90
Registered: April 2009
Location: Silver Spring

Member

I run 2 MECs w/ 16-in and 8-out on each. I have a Mackie 1402 that I use to some the outputs of MEC 1 and MEC 2 when necessary but I seldom do so. I usually give the players the same mix as I listen to in the CR which uses only the main out from MEC 1. I also have a Lexicon PCM 91 reverb which I drive with a parallel ocnnect from MECs 1 and 2. The digital out of the PCM 91 returns to the digi in of MEC 1. I seldom run other outboard but when I do I just use analog I/O from the MECs.

HOpe this helps!

Gantt

mono wrote on Fri, 02 July 2010 04:44

Can i mix/sum my channels external in some paris config????

Report message to a moderator

Re: external mixing/summing [message #105390 is a reply to message #105389]

Fri, 02 July 2010 10:01

mono

Messages: 20
Registered: August 2006
Location: netherlands

Junior Member

Thanks for the reply.

I wonder how you configure the patchbay?
Could you perhaps post a screenshot off it?

So i guess you got the channels going into the mackie.
And the mackie's mainmix is routed to?

I don't need the gear, the gear needs me.

Report message to a moderator

Re: external mixing/summing [message #105391 is a reply to message #105390]

Fri, 02 July 2010 10:17

ganttmann1

Messages: 90
Registered: April 2009
Location: Silver Spring

Member

I send my main mix outs (NOT CR outs, which "hear" solo tracks) to MEC 1 outs 3 & 4 => Mackie line in =>. Aux bus 1-2 is routed to "external", then in PB those outs go to MEC 1 outs 5 & 6. MEC 2 outs 1 & 2 are paralleled with those thru my "real" patchbay to the inputs of my PCM 91which returns digitally to the MEC 1 Master module's digi inputs. Mix out of the Mackie goes to my Coleman Audio TB-4 (inserts talkback and controls routing) => my cue amp inputs => headphone distribution.

THere is also a way to create headphone mixes using aux sends that are unaffected by mixer changes but I rarely do that.

Does that make sense? I'm not in the studio so I can't make screenshots...

Gantt

mono wrote on Fri, 02 July 2010 13:01

Report message to a moderator