| Do not ever do this [message #70363] |
Mon, 17 July 2006 08:43  |
![Deej [1] is currently offline](/theme/PARIS_Forum_Template/images/offline.png "Deej [1] is currently offline")
Deej [1]
Messages: 2149
Registered: January 2006
|
Senior Member |
|
|
If you are clocking an RME HDSP card from a Paris ADAT card (or in my case
clocking 3 x RME cards from 3 x Paris ADAT cards) and, for convenience sake,
since you want to be able to monitor your HDSP I/O in Wavelab without
launching Paris in order to clock the HDSP cards and you are too f***'in
lazy to make one simple change in a digital patchbay GUI , you decide to
also hook one of the RME cards up directly to a WC feed from your external
clock that is also feeding your 4 x MECs which are then sending this WC sync
from the ADAT modules to the RME interfaces because "since the ADAT modules
are just regenerating the WC that they are receiving from the house clock
this should be the same" you will have loads of fun when both computers
start losing sync, and not only losing sync, but freezing completely,
requiring a hard reboot. Not only will it be fun while it's happening, but
you get the added benefit of having to actually shut down every computer and
digital device in the studio for a little while, then after they have calmed
down a little, start your boot sequence all over. The various devices may
still be pissed off at each other for a while and you may need to try a
couple of times before all of this stuff is willing to shake hands and play
nice.
That's about as simple as I can explain it.
;o)
|
|
|
|
| Re: Do not ever do this [message #70368 is a reply to message #70363] |
Mon, 17 July 2006 11:07  |
LaMont
Messages: 828
Registered: October 2005
|
Senior Member |
|
|
And your point??
:)
"DJ" <animix_spam-this-ahole_@animas.net> wrote:
>If you are clocking an RME HDSP card from a Paris ADAT card (or in my case
>clocking 3 x RME cards from 3 x Paris ADAT cards) and, for convenience sake,
>since you want to be able to monitor your HDSP I/O in Wavelab without
>launching Paris in order to clock the HDSP cards and you are too f***'in
>lazy to make one simple change in a digital patchbay GUI , you decide to
>also hook one of the RME cards up directly to a WC feed from your external
>clock that is also feeding your 4 x MECs which are then sending this WC
sync
>from the ADAT modules to the RME interfaces because "since the ADAT modules
>are just regenerating the WC that they are receiving from the house clock
>this should be the same" you will have loads of fun when both computers
>start losing sync, and not only losing sync, but freezing completely,
>requiring a hard reboot. Not only will it be fun while it's happening, but
>you get the added benefit of having to actually shut down every computer
and
>digital device in the studio for a little while, then after they have calmed
>down a little, start your boot sequence all over. The various devices may
>still be pissed off at each other for a while and you may need to try a
>couple of times before all of this stuff is willing to shake hands and play
>nice.
>
>
>That's about as simple as I can explain it.
>
>;o)
>
>
|
|
|
|
| Re: Do not ever do this [message #70380 is a reply to message #70368] |
Mon, 17 July 2006 14:00 |
Deej [1]
Messages: 2149
Registered: January 2006
|
Senior Member |
|
|
I figured a bunch of folks were on the brink of going down this road and it
was my duty to stop them before it was too late.......of course
;o)
"LaMont Davis" <jjdpro@ameritech.net> wrote in message
news:44bbd1e5$1@linux...
>
> And your point??
> :)
> "DJ" <animix_spam-this-ahole_@animas.net> wrote:
> >If you are clocking an RME HDSP card from a Paris ADAT card (or in my
case
> >clocking 3 x RME cards from 3 x Paris ADAT cards) and, for convenience
sake,
> >since you want to be able to monitor your HDSP I/O in Wavelab without
> >launching Paris in order to clock the HDSP cards and you are too f***'in
> >lazy to make one simple change in a digital patchbay GUI , you decide to
> >also hook one of the RME cards up directly to a WC feed from your
external
> >clock that is also feeding your 4 x MECs which are then sending this WC
> sync
> >from the ADAT modules to the RME interfaces because "since the ADAT
modules
> >are just regenerating the WC that they are receiving from the house clock
> >this should be the same" you will have loads of fun when both computers
> >start losing sync, and not only losing sync, but freezing completely,
> >requiring a hard reboot. Not only will it be fun while it's happening,
but
> >you get the added benefit of having to actually shut down every computer
> and
> >digital device in the studio for a little while, then after they have
calmed
> >down a little, start your boot sequence all over. The various devices may
> >still be pissed off at each other for a while and you may need to try a
> >couple of times before all of this stuff is willing to shake hands and
play
> >nice.
> >
> >
> >That's about as simple as I can explain it.
> >
> >;o)
> >
> >
>
|
|
|
|
The PARIS Forums
Search
Help
Members
Register
Login
Home
