|
|
|
|
| Re: How to configure a floating A/D/D/A converter for Paris [message #58340 is a reply to message #58339] |
Mon, 19 September 2005 23:00   |
![Deej [1] is currently offline](/theme/PARIS_Forum_Template/images/offline.png "Deej [1] is currently offline")
Deej [1]
Messages: 2149
Registered: January 2006
|
Senior Member |
|
|
;/FONT></DIV>
<DIV><FONT face=3DArial size=3D2>modern with =
taste.</FONT></DIV></BODY></HTML>
------=_NextPart_000_001D_01C5BD87.48C87AE0--"Kim" <hiddensounds@hotmail.com> wrote:
>
>
>So what happens if I just plug in a mono 1/4 inch jack, which I'm guessing
>will simply short one of the balanced pair to ground. Is this bad for the
>preamp or is there so much resistance in the circuit that it doesn't really
>hurt it because it's not that bigger short (because there's resistors elsewhere
>in the circuit)?
>
>Just wondering if I need to wire special leads for this...
>
>Cheers,
>Kim.
If the output of the pre is transformer coupled, you must tie the negative
side to ground if you can’t do bal-bal.
If the pre is electronically driven, you should generally let the negative
pin float. Some active drivers don’t mind driving directly to ground, but
some do. It’s best to check with the manufacturer.
GeneYou cam use the wires under 98and |Me.
Just install the subsystem as you would do if you had XP.
I run Me and I have the wires showing up.
I have never tried under 98SE but I assume that if Me does it why not
win98SE .....
Regards,
Dimitrios
"Jeff Batter" <jeffbatter@cox.net> wrote in message news:432f6349$1@linux...
>
> I'm running it on 98se.
> I guess I'm out of luck for that one.
> I need to have use of the ADAT in and out, even
> though I'm not synching to ADATS
>
> No such luck with 98se?
>
> Thanks,
> Jeff
>
>
> EK Sound <spamnot.info@eksoundNO.com> wrote:
> >If you are running on WinXP with the new FX subsystem installed, wires
> >will show up as an EDS plug on the inserts.
> >
> >David.
> >
> >Jeff Batter wrote:
> >> This is what I get from being awol so much...
> >>
> >> When was Paris wires released? and where would I go to get it?
> >>
> >> Thanks,
> >> Jeff
> >>
> >>
> >> "Don Nafe" <dnafe@magma.ca> wrote:
> >>
> >>>Found it...DUH!
> >>>
> >>>Don
> >>>
> >>>"Don Nafe" <dnafe@magma.ca> wrote in message news:432d7a3b@linux...
> >>>
> >>>>Hi All
> >>>>
> >>>>I just rebuilt my computer and averything is working nicely but I
noticed
> >>
> >>
> >>>>Wires is missing on the FX list...where can I find it?
> >>>>
> >>>>thanks
> >>>>
> >>>>Don
> >>>>
> >>>>
> >>>>
> >>>>
> >>>
> >>>
> >>
>That's almost exactly what I suspected.
It's an electronic pre, so I guess I'll have to go the "keep the negative
lifted" route to be sure.
Thanks. :o)
Cheers,
Kim.
"gene lennon" <glennon@NOSPmyrealbox.com> wrote:
>
>"Kim" <hiddensounds@hotmail.com> wrote:
>>
>>
>>So what happens if I just plug in a mono 1/4 inch jack, which I'm guessing
>>will simply short one of the balanced pair to ground. Is this bad for the
>>preamp or is there so much resistance in the circuit that it doesn't really
>>hurt it because it's not that bigger short (because there's resistors elsewhere
>>in the circuit)?
>>
>>Just wondering if I need to wire special leads for this...
>>
>>Cheers,
>>Kim.
>
>If the output of the pre is transformer coupled, you must tie the negative
>side to ground if you can’t do bal-bal.
>
>If the pre is electronically driven, you should generally let the negative
>pin float. Some active drivers don’t mind driving directly to ground, but
>some do. It’s best to check with the manufacturer.
>Gene
>i knew that was you...i knew that was you...hoooooweeeeeee...dang!
On Tue, 20 Sep 2005 00:00:53 -0600, "DJ"
<animix_spam-this-ahole_@animas.net> wrote:
>......but no simpler than necessary.
>
>;o)Often it stands in the manual if the preamps can use both unbalanced or
balanced jacks. I know most of my preamps can use both. If you don't have a
manual, for the most you can find one on the net.
Erling
"Kim" <hiddensounds@hotmail.com> skrev i melding news:432fd1a4$1@linux...
>
>
> That's almost exactly what I suspected.
>
> It's an electronic pre, so I guess I'll have to go the "keep the negative
> lifted" route to be sure.
>
> Thanks. :o)
>
> Cheers,
> Kim.
>
> "gene lennon" <glennon@NOSPmyrealbox.com> wrote:
>>
>>"Kim" <hiddensounds@hotmail.com> wrote:
>>>
>>>
>>>So what happens if I just plug in a mono 1/4 inch jack, which I'm
>>>guessing
>>>will simply short one of the balanced pair to ground. Is this bad for the
>>>preamp or is there so much resistance in the circuit that it doesn't
>>>really
>>>hurt it because it's not that bigger short (because there's resistors
>>>elsewhere
>>>in the circuit)?
>>>
>>>Just wondering if I need to wire special leads for this...
>>>
>>>Cheers,
>>>Kim.
>>
>>If the output of the pre is transformer coupled, you must tie the negative
>>side to ground if you can't do bal-bal.
>>
>>If the pre is electronically driven, you should generally let the negative
>>pin float. Some active drivers don't mind driving directly to ground, but
>>some do. It's best to check with the manufacturer.
>>Gene
>>
>UGGGGHHH this one will take a while to get over
"Perry" <puigar@yahoo.com> wrote:
>
>Wheeeew!!!
>
>
>"James McCloskey" <excelsm@hotmail.com> wrote:
>>
>>It was good for a laugh; ) This is more like the final insult! Ah, now
>>look what happened to big hair metal!
>>
>>"DC" <dc@spamthesinger.org> wrote:
>>>
>>>http://reservoirstock.free.fr/deep%20sunshine%201.wmv
>>>
>>>I warned you...
>Thanks much Dim
|
|
|
|
|
|
|
|
The PARIS Forums
Search
Help
Members
Register
Login
Home
