Home » The PARIS Forums » PARIS: Main » ASIO DRIVER current status ?
|
Re: ASIO DRIVER current status ? [message #110223 is a reply to message #110222] |
Sun, 15 October 2023 08:59 |
danielcornelius
Messages: 171 Registered: May 2012
|
Senior Member |
|
|
Hi Mike,
i have bought the new Driver from your webside, i am glad to donate you in that way.
I have some issue, that i can't solve by myself now.
My Asio Host Cubase 12 freeze after choosing the Paris asio driver and the Paris Software too.
I have selected, Cubase 12 runs as Administrator.
What could it be, that booth freeze after starting the MEC ?
The MEC is loaded with 1x Input Card, 1X Output Card an 2x Adat.
These days is no CS16 used.
The Device Manager shows, all is raedy and alright.
If you know nothing about that, is it possible to show with team Viewer into my system ?
Best regards !
Daniel
----------------------------
- Asio Driver Cubase 5LE,Cubase 12
- Asus Z97-C, LGA 1150
- Intel i5 2320
- 32GB RAM
- 4x Seagate Barracuda 750GB
- Win10 64 bit
|
|
|
|
Re: ASIO DRIVER current status ? [message #110225 is a reply to message #110224] |
Sun, 15 October 2023 12:41 |
danielcornelius
Messages: 171 Registered: May 2012
|
Senior Member |
|
|
Hi Mike,
I am using the pci expansions Slots of the Motherboard. I am using the old Asus Z97 C ..with 32GB Ram
Best regards
Daniel
----------------------------
- Asio Driver Cubase 5LE,Cubase 12
- Asus Z97-C, LGA 1150
- Intel i5 2320
- 32GB RAM
- 4x Seagate Barracuda 750GB
- Win10 64 bit
[Updated on: Sun, 15 October 2023 12:42] Report message to a moderator
|
|
|
|
|
Re: ASIO DRIVER current status ? [message #110228 is a reply to message #110227] |
Mon, 16 October 2023 18:39 |
mikeaudet
Messages: 477 Registered: February 2009 Location: Canada
|
Senior Member |
|
|
Hi Dan,
Unfortunately, freezing almost always indicates a hardware error. Generally, if I make a mistake in the driver code, the blue screen of death results. The only exception to this that I've ever seen is in power management code (when the PC is waking up), which isn't in the version of the driver you have. I'd remove the PCI card from the slot and put it back it. If you have another PCI slot, it might make sense to try the other slot.
The PARIS app will open if only one card is in the system and there is no interface attached. If you have another card, I'd try just the one card with no interface, and see if PARIS.exe starts up. make sure PARIS.exe is running as administrator. If it isn't running as administrator, PARIS.exe will crash, but I have not seen it make the PC freeze.
I've attached an image of the damage to the female SCSI connector on an EDS 1000 card from a 50 pin cable with a bent pin. Take a look at your card and MEC connectors to see if anything looks like this. The power for the 442 flows on one of the edge pins, and if the pin gets bent, it can apply power to signal pins on one of the chips on the card or the MEC and damage it.
I installed the second version of the ASIO on my test PC under Windows 10, applied all Windows 10 updates, and it worked fine.
I'm happy to take a look on TeamViewer tomorrow after work (after 6:00pm Eastern Daylight Time).
I hope this helps,
Mike
|
|
|
|
|
Goto Forum:
Current Time: Fri Dec 13 12:21:47 PST 2024
Total time taken to generate the page: 0.01597 seconds
|