The PARIS Forums: PARIS: Main » EDS cards not connected properly

Home » The PARIS Forums » PARIS: Main » EDS cards not connected properly

Show: Today's Messages :: Polls :: Message Navigator

EDS cards not connected properly [message #109557]

Fri, 28 September 2018 11:21

Nuobu

Messages: 4
Registered: January 2015

Junior Member

Hello everyone,

I'm having difficulty troubleshooting this problem.

I had the Paris system working before my PC broke down. After getting the program back and plugging in the MEC and my Magma chassis with the same configuration, I keep getting the message that the EDS cards are 'not connected properly.' Paris will launch after this message but as it warns in the error message, there are severe playback issues for me.

I have tried using just one EDS card and I seem to get a 1/1 error. I have tried several PCI slots in my chassis, same thing. I've tried switching the cable around between my two cards, but then I get the message that nothing is connected to the master card, when plugged into the other.

I seem to have only three of the small cables connecting the cards, which are plugged into the 1, 2 and 4 terminals, so there's nothing on the third one, am I missing a cable somehow?

Any help would be massively appreciated,

Thanks

Report message to a moderator

Re: EDS cards not connected properly [message #109558 is a reply to message #109557]

Sat, 29 September 2018 05:33

Nuobu

Messages: 4
Registered: January 2015

Junior Member

OK, so I have got past this problem (by Reading the effing manual Embarassed

) My connectors were in the wrong way. I don't remember having this problem before my computer broke down, that's why I didn't check the connections at first...

However,

After playing around in Paris for a bit, I started to get the following message upon startp:

ASSERTION FAILED NativeFxlibrary.cpp:191((LibraryHeader*)libData)->tag==kLibTag

I searched the forum for this problem and tried moving my plugins folder to another location to no avail. The only change I've made on my computer within that time is to install a Wave editor program, so I will try to uninstall that I suppose?

Any other ideas would be great, thanks again

[Updated on: Sat, 29 September 2018 14:12]

Report message to a moderator

Re: EDS cards not connected properly [message #109559 is a reply to message #109557]

Thu, 04 October 2018 07:05

Will The Weirdo

Messages: 190
Registered: December 2009
Location: On The Lake

Senior Member

Nuobu wrote on Fri, 28 September 2018 11:21

Any help would be massively appreciated,

Stick testing with one card for now, use an eraser and clean the metal PCI pins as they get dirty over time and can loose connection. They will shine up quick so you'll know they are clean and remember to carefully clean the pins while holding the outside of the EDS card only, do not get any skin oil on it. Once clean re-seat the PCI card than see if that fixes your issue.

[Updated on: Thu, 04 October 2018 07:07]

Report message to a moderator

Re: EDS cards not connected properly [message #109564 is a reply to message #109557]

Tue, 09 October 2018 17:27

Kim W.

Messages: 189
Registered: January 2010
Location: Australia

Senior Member

I don't know if this helps, but on several occasions, my Paris.cfg file has inexplicably been wiped clean. Check that the file still has all the settings intact. MAKE A BACKUP!! You can open it with any text editor.
Regards,
Kim.

Report message to a moderator

Previous Topic:	Exporting an old PARIS project
Next Topic:	c 16 outside of paris

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Fri Nov 01 05:22:11 PDT 2024

Total time taken to generate the page: 0.01189 seconds