Home » The PARIS Forums » PARIS: Main » Never thought it possible! Thanks Mike, Kerry, Matt etc. (New box working! 4 EDS's, Four monitors. No Chassis!)
| Never thought it possible! Thanks Mike, Kerry, Matt etc. [message #106287] |
Wed, 20 April 2011 16:03  |
Kim W.
Messages: 189
Registered: January 2010
Location: Australia
|
Senior Member |
|
|
I purchased mike's drivers some time ago, and bought a Gigabyte GA-M720-US3 mobo (NVIDIA chipset)at the same time. So far, so good! Using an OEM NVIDIA nvs 285 16X pci-e card, and a 1x pci-e Galaxy 7300GT card (with a small riser that clears the chipset heatsink). Four monitor outputs.. cool!
(The pics were taken from my kitchen "test bench".
If you can still get this mobo, and need to run 4 EDS's GET IT!
I shoved a quad core Athlon 2 @ 3000mhz in it, and all is sweet.
Looking forward to retiring my K8NS-ultra shortly!
Long Live Paris!!
-
Attachment: PARIS 1.JPG
(Size: 2.35MB, Downloaded 213 times)
-
Attachment: PARIS 2.JPG
(Size: 2.60MB, Downloaded 189 times)
[Updated on: Wed, 20 April 2011 16:20] by Moderator Report message to a moderator |
|
|
|
|
|
|
|
| Re: Never thought it possible! Thanks Mike, Kerry, Matt etc. [message #106298 is a reply to message #106296] |
Fri, 22 April 2011 08:23  |
Kim W.
Messages: 189
Registered: January 2010
Location: Australia
|
Senior Member |
|
|
Hi Colin.
I can say at this stage that the two graphics cards do play nicely together. (The fact that this mobo uses the a Nvidia chipset helps, I guess). I did have to use a riser adaptor for the 1x 7300GT card, however. I purchased it from an online store here in Australia called "Darkwire". The web site is under reconstruction right now, and I can't see it anywhere on the site. It is basically just a 1x riser, approx 2/3" high. This is necessary so that the 7300 can clear the mobo chipset heatsink. I had to find a spacer of equivalent length in order to bolt the card firmly into the case.
Something like this, however, should do the trick: (with the added bonus that you could probably mount the card in any of the hardware slots available in your case):a
http://www.dhgate.com/2-lots-pci-e-1x-riser-pci-express-card -extender/p-ff8080812b2e46df012b3f56726e6908.html
Also, if the 1x card is difficult to come by, I'm pretty sure that I had, at one stage, a 16x Nvidia card working nicely with the same adaptor. (with a slot cut at one end..) Apparently only the first 1/3rd of the pins on a pci-e card are needed, albeit with a SLIGHT performance hit. (I don't do gaming on my DAW).
There is plenty of info on this on the 'net.
Here is one such page:
http://forums.overclockers.com.au/showthread.php?t=656394
Anyways, I see no further problems arising, however I am yet to permanently move my other three EDS's into the new box, and do some testing. I am quite confident, however, and will keep you posted.
Cheers,
Kim
|
|
|
|
|
|
| Re: Never thought it possible! Thanks Mike, Kerry, Matt etc. [message #106320 is a reply to message #106299] |
Sat, 23 April 2011 11:48 |
Kim W.
Messages: 189
Registered: January 2010
Location: Australia
|
Senior Member |
|
|
OOh, I'm excited! Everything is working smoothly so far, with none of the hoops I had to jump through before. I'm stoked!
Attached is a screen dump of my quad core, four EDS, four C-16, four monitor setup. This box is also the quietest I've ever built for Paris! (..and I didn't need a magma or similar..)
Now for the dubious task of installing all my plugins.
Colin, if you can still get this mobo, get it while you can.
I noticed you are in Australia. You may be lucky! (It was dirt cheap at MSY... $110, but that was some time ago..)
It uses DDR2 ram, so you may like to get that too, before you start paying too much of a "premium", for legacy hardware.
As far as processors are concerned, no problem. The mobo is good for a six core phenom, I believe.
Next test will be to load up a 64 track project, once I install the necessary plugins.
|
|
|
|
|
|
|
|
|
|
| Re: Never thought it possible! Thanks Mike, Kerry, Matt etc. [message #106335 is a reply to message #106323] |
Tue, 26 April 2011 04:03 |
Kim W.
Messages: 189
Registered: January 2010
Location: Australia
|
Senior Member |
|
|
Hi Colin.
I tried PM'ing you but you have disabled PM'ing. 
If you can PM me your email address, we can talk about it, and not clog up this forum. It's a bit complicated, but the supplier doesn't do mail-order, but I *think* I have secured the very last two of these mobos in the country. (courtesy of a friend in Victoria). (One is a spare for myself, in case of power surge etc, and the other, well, I may keep as another spare because I have a second PC running a 32 channel Frontier Dakota system,(also PCI-based) which is sync'd to my Paris box, via ADAT).
Also, How many EDS cards do you intend to use?
What I'm suggesting is: If you are migrating to PC land, and IF you REALLY need four PCI slots, (four EDS cards), and IF you can prove you have paid for both the Paris 3 software, AND Mike's multicore drivers, (and IF I get these mobos - still unknown), I could make an image of the raw install that I've created, and send it to you on DVD-ROM. Then all you would have to do is to re-jig the drivers for your four-monitor setup, if they differ from mine).
I'm running four 22" LG widescreen monitors, and all is well.
Cheers,
Kim
|
|
|
|
|
|
Goto Forum:
Current Time: Sun Nov 24 21:45:58 PST 2024
Total time taken to generate the page: 0.01110 seconds
|
The PARIS Forums
Search
Help
Members
Register
Login
Home
