The PARIS Forums: PARIS: Main

Home » The PARIS Forums » PARIS: Main » 2 MEC and 2 EDS (Step by step setup procedure for recording with 2 MEC and 2 EDS wanted)

Show: Today's Messages :: Polls :: Message Navigator

2 MEC and 2 EDS [message #105877]

Wed, 22 December 2010 23:00

jpopelka

Messages: 3
Registered: December 2010

Junior Member

Could anybody help me to make 2 MEC and 2 EDS to work as one system?
Jerry

Report message to a moderator

Re: 2 MEC and 2 EDS [message #105878 is a reply to message #105877]

Thu, 23 December 2010 08:20

dnafe

Messages: 390
Registered: February 2009

Senior Member

have you got them connected via work clock?

Report message to a moderator

Re: 2 MEC and 2 EDS [message #105879 is a reply to message #105878]

Thu, 23 December 2010 09:51

jpopelka

Messages: 3
Registered: December 2010

Junior Member

Somewhere I read that more than two MEC have to be connected through external wordclock device.
Is it necessary even for just two MECs?

Report message to a moderator

Re: 2 MEC and 2 EDS [message #105880 is a reply to message #105879]

Thu, 23 December 2010 14:39

dnafe

Messages: 390
Registered: February 2009

Senior Member

yes three or more will need a WC generator or distribution amp but two MECs still need to be connected via wordclock for them to be in sync

Report message to a moderator

Re: 2 MEC and 2 EDS [message #105881 is a reply to message #105880]

Sun, 26 December 2010 18:43

echopraxia

Messages: 32
Registered: September 2010

Member

I am curious about this too as I have two mecs and just one eds card. When I get a second card do I need to connect them internally inside the PC with ribbon cable or can I just use a BNC word clock cable between the two mecs and be good to go? Alternatively If I only connect them internally do I still need to use a wc cable between the two mecs?

Report message to a moderator

Re: 2 MEC and 2 EDS [message #105882 is a reply to message #105881]

Mon, 27 December 2010 03:40

dnafe

Messages: 390
Registered: February 2009

Senior Member

You'll need to wire them intermally with the ribbon and crossover cables

I made the assumption that the OP has them connected this way, if not, he too will have to connect his EDS cards together via the cables

Adding the WC cable insures the hardware is sync'd

[Updated on: Mon, 27 December 2010 03:43]

Report message to a moderator

Re: 2 MEC and 2 EDS [message #105885 is a reply to message #105882]

Mon, 27 December 2010 07:19

jpopelka

Messages: 3
Registered: December 2010

Junior Member

BTW the ribbon cables were shipped just with the second EDS card, so when I own two MEC and two EDS there are no connection cables to connect internally two EDS.
Does anybody know if they are some common type cables or specifically designed for Paris?
Jerry

Report message to a moderator

Re: 2 MEC and 2 EDS [message #105886 is a reply to message #105885]

Mon, 27 December 2010 07:40

dnafe

Messages: 390
Registered: February 2009

Senior Member

I think Kerry had a source for those cables if I'm not mistaken

Report message to a moderator

Re: 2 MEC and 2 EDS [message #105892 is a reply to message #105886]

Thu, 30 December 2010 01:14

imajon

Messages: 55
Registered: June 2009
Location: Wisconsin

Member

I made my cables from ribbon cables from old hard drive cables and the connector I picked up at an electronics store. I just peeled off the the appropriate wire count and added the connectors. I have a 3 card system and 2 Mecs. You have to sync both Mecs with word clock. I use an external clock but I believe you can with the internal clock with cable from clock out from one mec to clock in of second mec. If you use an external clock you must set Paris to "external in the control panel and also change "UseHouseSync=0" to "UseHouseSync=1" in the paris.cfg file. Also set the card that is attached to the mec supplying the house sync as master card.

Report message to a moderator

Re: 2 MEC and 2 EDS [message #105895 is a reply to message #105892]

Fri, 31 December 2010 04:16

mani1147

Messages: 130
Registered: May 2009
Location: NB Canada

Senior Member

Hi Imajon, see this tread for images of the ribbon cable config between multiple EDS cards. This is my last Paris PC build with the i7.

Those cables are a bit hard to find but in a pinch, you can make some using old IDE cables, an exacto knife, elec tape and a hack saw...!!!

Good luck
Rob_A

Report message to a moderator

Previous Topic:	No reverb eds plugin???
Next Topic:	Windows7

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Mon Feb 03 16:26:48 PST 2025

Total time taken to generate the page: 0.01253 seconds