The PARIS Forums


Home » The PARIS Forums » PARIS: Main » DOuble Checking PUAD Plate sample Slide values
DOuble Checking PUAD Plate sample Slide values [message #94751] Tue, 15 January 2008 20:26 Go to next message
Cujjo is currently offline  Cujjo   
Messages: 325
Registered: June 2007
Senior Member
I've been using the UAD Plate 140 for a while now, and today I tried it on
Acoustic Guitar..for fun, but I'm finding it seems to have some phase cancellation
at 1536 sample nudge (4X100 slip)..Is this an incorrect value? It was easier
to hear on acoustic (drop d tuning) than on the lead vocals, I'm guessing
due to the more low end content is the reason
Re: DOuble Checking PUAD Plate sample Slide values [message #94759 is a reply to message #94751] Wed, 16 January 2008 06:03 Go to previous messageGo to next message
Phil Aiken is currently offline  Phil Aiken
Messages: 62
Registered: February 2008
Member
C -
Put it on a track insert next to a duplicate track and set it to 100%
dry. Should be very easy to tell aurally, but yo can also render the effected
track and look at the wave forms. Then, start planning your Super Bowl party.
-P

"CUjo" <chris@applemanstudio.com> wrote:
>
>
>
>I've been using the UAD Plate 140 for a while now, and today I tried it
on
>Acoustic Guitar..for fun, but I'm finding it seems to have some phase cancellation
>at 1536 sample nudge (4X100 slip)..Is this an incorrect value? It was easier
>to hear on acoustic (drop d tuning) than on the lead vocals, I'm guessing
>due to the more low end content is the reason
Re: DOuble Checking PUAD Plate sample Slide values [message #94760 is a reply to message #94759] Wed, 16 January 2008 07:28 Go to previous messageGo to next message
john Macy[2] is currently offline  john Macy[2]
Messages: 24
Registered: June 2008
Junior Member
I cut my recording teeth on 140's and we were always
putting a delay in front of them to separate them from
the original signal, so unless I am misunderstanding
something, time alignment should be no problem.



"Phil Aiken" <adfadfa@asdfa.asdaf> wrote:
>
>C -
> Put it on a track insert next to a duplicate track and set it to 100%
>dry. Should be very easy to tell aurally, but yo can also render the effected
>track and look at the wave forms. Then, start planning your Super Bowl party.
> -P
>
>"CUjo" <chris@applemanstudio.com> wrote:
>>
>>
>>
>>I've been using the UAD Plate 140 for a while now, and today I tried it
>on
>>Acoustic Guitar..for fun, but I'm finding it seems to have some phase cancellation
>>at 1536 sample nudge (4X100 slip)..Is this an incorrect value? It was easier
>>to hear on acoustic (drop d tuning) than on the lead vocals, I'm guessing
>>due to the more low end content is the reason
>
Re: DOuble Checking PUAD Plate sample Slide values [message #94763 is a reply to message #94759] Wed, 16 January 2008 08:22 Go to previous messageGo to next message
Cujjo is currently offline  Cujjo   
Messages: 325
Registered: June 2007
Senior Member
Are you going to come up?


"Phil Aiken" <adfadfa@asdfa.asdaf> wrote:
>
>C -
> Put it on a track insert next to a duplicate track and set it to 100%
>dry. Should be very easy to tell aurally, but yo can also render the effected
>track and look at the wave forms. Then, start planning your Super Bowl party.
> -P
>
>"CUjo" <chris@applemanstudio.com> wrote:
>>
>>
>>
>>I've been using the UAD Plate 140 for a while now, and today I tried it
>on
>>Acoustic Guitar..for fun, but I'm finding it seems to have some phase cancellation
>>at 1536 sample nudge (4X100 slip)..Is this an incorrect value? It was easier
>>to hear on acoustic (drop d tuning) than on the lead vocals, I'm guessing
>>due to the more low end content is the reason
>
Re: DOuble Checking PUAD Plate sample Slide values [message #94764 is a reply to message #94760] Wed, 16 January 2008 08:26 Go to previous message
Cujjo is currently offline  Cujjo   
Messages: 325
Registered: June 2007
Senior Member
On the UAD EMT, there is a pre-delay knob, I always use a bit.
Actually this could be tru when using a real EMT I suppose.
When I was at Paul Kolderies studio a few years back (Phil was there) I brought
my Roland 501 and we used it on vocals, we noticed that depending on the
input chosen, there would be cancellation.


"John Macy" <nospamjohn@johnmacy.com> wrote:
>
>I cut my recording teeth on 140's and we were always
>putting a delay in front of them to separate them from
>the original signal, so unless I am misunderstanding
>something, time alignment should be no problem.
>
>
>
>"Phil Aiken" <adfadfa@asdfa.asdaf> wrote:
>>
>>C -
>> Put it on a track insert next to a duplicate track and set it to
100%
>>dry. Should be very easy to tell aurally, but yo can also render the effected
>>track and look at the wave forms. Then, start planning your Super Bowl
party.
>> -P
>>
>>"CUjo" <chris@applemanstudio.com> wrote:
>>>
>>>
>>>
>>>I've been using the UAD Plate 140 for a while now, and today I tried it
>>on
>>>Acoustic Guitar..for fun, but I'm finding it seems to have some phase
cancellation
>>>at 1536 sample nudge (4X100 slip)..Is this an incorrect value? It was
easier
>>>to hear on acoustic (drop d tuning) than on the lead vocals, I'm guessing
>>>due to the more low end content is the reason
>>
>
Previous Topic: OT: Now THIS Is A Debate
Next Topic: Room acoustics measurement software
Goto Forum:
  


Current Time: Sun Dec 15 23:53:51 PST 2024

Total time taken to generate the page: 0.00822 seconds