The PARIS Forums: PARIS: Main

Home » The PARIS Forums » PARIS: Main » Paris tip

Show: Today's Messages :: Polls :: Message Navigator

Paris tip [message #106586]

Wed, 13 July 2011 02:22

Dimitrios

Messages: 1056
Registered: August 2005

Senior Member

Hi,
I don't know if many from you know that already but I would like to share.
If you connect your main outs on your Paris patchbay to out1 and out2 then any change in monitor level will affect your mixdown level volume !
BUT if you connect your main outs to dital out (even if you don't have anything connected at your digital output then you can change your monitor levels during mixdown without affecting the recrding level of your mixdown file.
I don't know if I made myself clear enouph here so I will try to rephrase soemhow.
Say that you monitor from your Mec's physical outputs 1 and 2 going to your main monitors.
Then whenever you try to mixdwon your song to a stereo paf or wav file , by changing the monitor level it AFFECTS also the recording level of your recording file.
In order to avoid this try to use the "dummy" digital outs for your main patchbay outs and your out1 and out2 for your monitor patchbay out.
Thus by changing the monitor level you avoid changing the volume of the recording file when mixing down.
Hope this helps.
If this was already widely known please let me know !!
Regards,
Dimitrios

Report message to a moderator

Re: Paris tip [message #106588 is a reply to message #106586]

Wed, 13 July 2011 06:42

Ted Gerber

Messages: 705
Registered: January 2009

Senior Member

HI Dimitrios -

I connect my monitor outs from 3 & 4 on my MEC (they say "Monitor") and I can adjust Control Room level without affecting internal mix down levels. I use the physical S/PDIF into external reverbs. I don't use MEC outputs 1 & 2 - the "Main" outs - at all.

Ted

Report message to a moderator

Re: Paris tip [message #106591 is a reply to message #106588]

Fri, 15 July 2011 12:44

Dimitrios

Messages: 1056
Registered: August 2005

Senior Member

Hi,
Never tried that !
Thanks for knowing...
Regards,
Dimitrios

Report message to a moderator

Re: Paris tip [message #106592 is a reply to message #106588]

Fri, 15 July 2011 13:00

kerryg

Messages: 1529
Registered: February 2009

Senior Member
Administrator

I use the Main pair to feed the artist's headphone amp (a Behringer PowerPlay) so I can mute the monitors in the control room or solo a track for closer inspection while recording a take without interfering with it.

"... being bitter is like swallowing poison and waiting for the other guy to die..." - anon

Report message to a moderator

Re: Paris tip [message #106604 is a reply to message #106586]

Fri, 22 July 2011 07:34

damien

Messages: 36
Registered: October 2008

Member

I use auxes for stereo cue mixes. mm Ok, limited to one submix until i get another mec and use the buss trick with spdif.
very good for cutting basics tracks live ; i don't use it for overdubs with alot of tracks already there.

- setup a pair of aux (let's say 1&2) pre-fader on all tracks and external.
- in patchbay, route FX 1 left (or right) to an output
- in patchbay, route FX 2 left (or right) to an output
- connect your two physical output to an headphone amp
- swithing on aux1 on a track you got it hard panned left
- swithing on aux2 on a track you got it hard panned right
- switching on aux1 & 2 on a track you got it center
- adjust your aux send levels to taste to get it everywhere in stereo field.

you can go up to four stereo mixes, without messing with your monitor mix.

I've never had such a good sound in my headphone in any studio before.

[Updated on: Fri, 22 July 2011 08:17]

Report message to a moderator

Previous Topic:	slaving Paris to adat clock sync
Next Topic:	paris on servers

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Sun Dec 29 18:26:15 PST 2024

Total time taken to generate the page: 0.00942 seconds