Home » The PARIS Forums » PARIS: Main » I/O MODULE NOT FOUND
| I/O MODULE NOT FOUND [message #98703] |
Fri, 09 May 2008 20:58  |
CED
Messages: 13
Registered: August 2007
|
Junior Member |
|
|
Anyone with ideas...I've been running Paris on 98SE for years, just last night
I go to open a project and get 2 error messages " I/O modules not available
in this configuration....bla, bla" I have had this before when I forget
to turn on the MEC, but it's on, I tried another cable...nada! any thoughts
? Thanks
|
|
|
|
|
|
| Re: I/O MODULE NOT FOUND [message #98716 is a reply to message #98704] |
Sat, 10 May 2008 11:03  |
CED
Messages: 13
Registered: August 2007
|
Junior Member |
|
|
Het Terry...I get this on opening a project, Also, I've done re-boots,
pulled and reset cards etc. Otherwise, Paris opens up as normal....I also
get no "sample rate" light showing........ "Terry Thomas" <god1stjt@alltel.net>
wrote:
>
>Hi Ced,
>
>Are you getting this messages when Paris starts up or just when you open
>a project?
>
>"Ced" <cedmo1@netzero.net> wrote:
>>
>>Anyone with ideas...I've been running Paris on 98SE for years, just last
>night
>>I go to open a project and get 2 error messages " I/O modules not available
>>in this configuration....bla, bla" I have had this before when I forget
>>to turn on the MEC, but it's on, I tried another cable...nada! any thoughts
>>? Thanks
>
|
|
|
|
| Re: I/O MODULE NOT FOUND [message #98720 is a reply to message #98716] |
Sat, 10 May 2008 15:27 |
Terry T
Messages: 32
Registered: February 2007
|
Member |
|
|
Hi Ced,
This normally happens when: (1)The power goes out and you're running dual
monitors but the settings show up on just one monitor (2)When you originally
did this project you were using only 1 Mec. You just need to reset your Patch
Bay configuration.
"ced" <cedmo1@netzero.net> wrote:
>
>
> Het Terry...I get this on opening a project, Also, I've done re-boots,
>pulled and reset cards etc. Otherwise, Paris opens up as normal....I also
>get no "sample rate" light showing........ "Terry Thomas" <god1stjt@alltel.net>
>wrote:
>>
>>Hi Ced,
>>
>>Are you getting this messages when Paris starts up or just when you open
>>a project?
>>
>>"Ced" <cedmo1@netzero.net> wrote:
>>>
>>>Anyone with ideas...I've been running Paris on 98SE for years, just last
>>night
>>>I go to open a project and get 2 error messages " I/O modules not available
>>>in this configuration....bla, bla" I have had this before when I forget
>>>to turn on the MEC, but it's on, I tried another cable...nada! any
thoughts
>>>? Thanks
>>
>
|
|
|
|
| Re: I/O MODULE NOT FOUND [message #98721 is a reply to message #98720] |
Sat, 10 May 2008 16:06 |
CED
Messages: 13
Registered: August 2007
|
Junior Member |
|
|
Hey Terry...unfortunately I've checked the patch bay and the MEC and 8in card
do not appear in it !"Terry Thomas" <god1stjt@alltel.net> wrote:
>
>Hi Ced,
>
>This normally happens when: (1)The power goes out and you're running dual
>monitors but the settings show up on just one monitor (2)When you originally
>did this project you were using only 1 Mec. You just need to reset your
Patch
>Bay configuration.
>
>"ced" <cedmo1@netzero.net> wrote:
>>
>>
>> Het Terry...I get this on opening a project, Also, I've done re-boots,
>>pulled and reset cards etc. Otherwise, Paris opens up as normal....I also
>>get no "sample rate" light showing........ "Terry Thomas" <god1stjt@alltel.net>
>>wrote:
>>>
>>>Hi Ced,
>>>
>>>Are you getting this messages when Paris starts up or just when you open
>>>a project?
>>>
>>>"Ced" <cedmo1@netzero.net> wrote:
>>>>
>>>>Anyone with ideas...I've been running Paris on 98SE for years, just last
>>>night
>>>>I go to open a project and get 2 error messages " I/O modules not available
>>>>in this configuration....bla, bla" I have had this before when I forget
>>>>to turn on the MEC, but it's on, I tried another cable...nada! any
>thoughts
>>>>? Thanks
>>>
>>
>
|
|
|
|
| Re: I/O MODULE NOT FOUND [message #98729 is a reply to message #98721] |
Sat, 10 May 2008 20:32 |
Terry T
Messages: 32
Registered: February 2007
|
Member |
|
|
Hey Ced,
Check with Mike Audet or Aaron Allen on this problem. Sometime if you have
two Mec Interface in the Patching area configurated (like A&B) and you save
it; but, you are really only using "A" then you will get this message.
"ced" <cedmo1@netzero.net> wrote:
>
>Hey Terry...unfortunately I've checked the patch bay and the MEC and 8in
card
>do not appear in it !"Terry Thomas" <god1stjt@alltel.net> wrote:
>>
>>Hi Ced,
>>
>>This normally happens when: (1)The power goes out and you're running dual
>>monitors but the settings show up on just one monitor (2)When you originally
>>did this project you were using only 1 Mec. You just need to reset your
>Patch
>>Bay configuration.
>>
>>"ced" <cedmo1@netzero.net> wrote:
>>>
>>>
>>> Het Terry...I get this on opening a project, Also, I've done re-boots,
>>>pulled and reset cards etc. Otherwise, Paris opens up as normal....I
also
>>>get no "sample rate" light showing........ "Terry Thomas" <god1stjt@alltel.net>
>>>wrote:
>>>>
>>>>Hi Ced,
>>>>
>>>>Are you getting this messages when Paris starts up or just when you open
>>>>a project?
>>>>
>>>>"Ced" <cedmo1@netzero.net> wrote:
>>>>>
>>>>>Anyone with ideas...I've been running Paris on 98SE for years, just
last
>>>>night
>>>>>I go to open a project and get 2 error messages " I/O modules not available
>>>>>in this configuration....bla, bla" I have had this before when I forget
>>>>>to turn on the MEC, but it's on, I tried another cable...nada! any
>>thoughts
>>>>>? Thanks
>>>>
>>>
>>
>
|
|
|
|
| Re: I/O MODULE NOT FOUND [message #98730 is a reply to message #98721] |
Sat, 10 May 2008 21:04 |
CED
Messages: 13
Registered: August 2007
|
Junior Member |
|
|
"ced" <cedmo1@netzero.net> wrote:
>
>Hey Terry...unfortunately I've checked the patch bay and the MEC and 8in
card
>do not appear in it !"Terry Thomas" <god1stjt@alltel.net> wrote:
>>
>>Hi Ced,
>>
>>This normally happens when: (1)The power goes out and you're running dual
>>monitors but the settings show up on just one monitor (2)When you originally
>>did this project you were using only 1 Mec. You just need to reset your
>Patch
>>Bay configuration.
>>
>>"ced" <cedmo1@netzero.net> wrote:
>>>
>>>
>>> Het Terry...I get this on opening a project, Also, I've done re-boots,
>>>pulled and reset cards etc. Otherwise, Paris opens up as normal....I
also
>>>get no "sample rate" light showing........ "Terry Thomas" <god1stjt@alltel.net>
>>>wrote:
>>>>
>>>>Hi Ced,
>>>>
>>>>Are you getting this messages when Paris starts up or just when you open
>>>>a project?
>>>>
>>>>"Ced" <cedmo1@netzero.net> wrote:
>>>>>
>>>>>Anyone with ideas...I've been running Paris on 98SE for years, just
last
>>>>night
>>>>>I go to open a project and get 2 error messages " I/O modules not available
>>>>>in this configuration....bla, bla" I have had this before when I forget
>>>>>to turn on the MEC, but it's on, I tried another cable...nada! any
>>thoughts
>>>>>? Thanks
>>>>
>>>
>>
>
|
|
|
|
| Re: I/O MODULE NOT FOUND [message #98731 is a reply to message #98721] |
Sat, 10 May 2008 21:10 |
CED
Messages: 13
Registered: August 2007
|
Junior Member |
|
|
well....I'm going to reply to my own call for help...Steve "Artguy" generously
lent me his gear in order to troubleshoot by item....problem seems to be
in the EDS 1000 card, don't know what the problem is exactly as everything
works except the MEC is not found in the patch bay , but replacing my card
has the system up and running again. Any follow-up ideas will be welcome.
"ced" <cedmo1@netzero.net> wrote:
>
>Hey Terry...unfortunately I've checked the patch bay and the MEC and 8in
card
>do not appear in it !"Terry Thomas" <god1stjt@alltel.net> wrote:
>>
>>Hi Ced,
>>
>>This normally happens when: (1)The power goes out and you're running dual
>>monitors but the settings show up on just one monitor (2)When you originally
>>did this project you were using only 1 Mec. You just need to reset your
>Patch
>>Bay configuration.
>>
>>"ced" <cedmo1@netzero.net> wrote:
>>>
>>>
>>> Het Terry...I get this on opening a project, Also, I've done re-boots,
>>>pulled and reset cards etc. Otherwise, Paris opens up as normal....I
also
>>>get no "sample rate" light showing........ "Terry Thomas" <god1stjt@alltel.net>
>>>wrote:
>>>>
>>>>Hi Ced,
>>>>
>>>>Are you getting this messages when Paris starts up or just when you open
>>>>a project?
>>>>
>>>>"Ced" <cedmo1@netzero.net> wrote:
>>>>>
>>>>>Anyone with ideas...I've been running Paris on 98SE for years, just
last
>>>>night
>>>>>I go to open a project and get 2 error messages " I/O modules not available
>>>>>in this configuration....bla, bla" I have had this before when I forget
>>>>>to turn on the MEC, but it's on, I tried another cable...nada! any
>>thoughts
>>>>>? Thanks
>>>>
>>>
>>
>
|
|
|
|
| Re: I/O MODULE NOT FOUND [message #98732 is a reply to message #98731] |
Sat, 10 May 2008 22:41 |
steve the artguy
Messages: 308
Registered: June 2005
|
Senior Member |
|
|
bummer, Ced-
maybe it can be repaired... maybe a new (used) one would be cheaper.
=steve
"ced" <cedmo1@netzero.net> wrote:
>
>well....I'm going to reply to my own call for help...Steve "Artguy" generously
>lent me his gear in order to troubleshoot by item....problem seems to be
>in the EDS 1000 card, don't know what the problem is exactly as everything
>works except the MEC is not found in the patch bay , but replacing my card
>has the system up and running again. Any follow-up ideas will be welcome.
>
> "ced" <cedmo1@netzero.net> wrote:
>>
>>Hey Terry...unfortunately I've checked the patch bay and the MEC and 8in
>card
>>do not appear in it !"Terry Thomas" <god1stjt@alltel.net> wrote:
>>>
>>>Hi Ced,
>>>
>>>This normally happens when: (1)The power goes out and you're running dual
>>>monitors but the settings show up on just one monitor (2)When you originally
>>>did this project you were using only 1 Mec. You just need to reset your
>>Patch
>>>Bay configuration.
>>>
>>>"ced" <cedmo1@netzero.net> wrote:
>>>>
>>>>
>>>> Het Terry...I get this on opening a project, Also, I've done re-boots,
>>>>pulled and reset cards etc. Otherwise, Paris opens up as normal....I
>also
>>>>get no "sample rate" light showing........ "Terry Thomas" <god1stjt@alltel.net>
>>>>wrote:
>>>>>
>>>>>Hi Ced,
>>>>>
>>>>>Are you getting this messages when Paris starts up or just when you
open
>>>>>a project?
>>>>>
>>>>>"Ced" <cedmo1@netzero.net> wrote:
>>>>>>
>>>>>>Anyone with ideas...I've been running Paris on 98SE for years, just
>last
>>>>>night
>>>>>>I go to open a project and get 2 error messages " I/O modules not
available
>>>>>>in this configuration....bla, bla" I have had this before when I
forget
>>>>>>to turn on the MEC, but it's on, I tried another cable...nada! any
>>>thoughts
>>>>>>? Thanks
>>>>>
>>>>
>>>
>>
>
|
|
|
|
| Re: I/O MODULE NOT FOUND [message #98733 is a reply to message #98731] |
Sun, 11 May 2008 02:39 |
Aaron Allen
Messages: 1988
Registered: May 2008
|
Senior Member |
|
|
It's likely that you have a bent pin somewhere on the EDS at the SCSI 50 pin
connection. Inspect it _carefully_ for any bent or broken connections.
AA
"ced" <cedmo1@netzero.net> wrote in message news:482671a1$1@linux...
>
> well....I'm going to reply to my own call for help...Steve "Artguy"
> generously
> lent me his gear in order to troubleshoot by item....problem seems to be
> in the EDS 1000 card, don't know what the problem is exactly as
> everything
> works except the MEC is not found in the patch bay , but replacing my card
> has the system up and running again. Any follow-up ideas will be welcome.
>
> "ced" <cedmo1@netzero.net> wrote:
>>
>>Hey Terry...unfortunately I've checked the patch bay and the MEC and 8in
> card
>>do not appear in it !"Terry Thomas" <god1stjt@alltel.net> wrote:
>>>
>>>Hi Ced,
>>>
>>>This normally happens when: (1)The power goes out and you're running dual
>>>monitors but the settings show up on just one monitor (2)When you
>>>originally
>>>did this project you were using only 1 Mec. You just need to reset your
>>Patch
>>>Bay configuration.
>>>
>>>"ced" <cedmo1@netzero.net> wrote:
>>>>
>>>>
>>>> Het Terry...I get this on opening a project, Also, I've done re-boots,
>>>>pulled and reset cards etc. Otherwise, Paris opens up as normal....I
> also
>>>>get no "sample rate" light showing........ "Terry Thomas"
>>>><god1stjt@alltel.net>
>>>>wrote:
>>>>>
>>>>>Hi Ced,
>>>>>
>>>>>Are you getting this messages when Paris starts up or just when you
>>>>>open
>>>>>a project?
>>>>>
>>>>>"Ced" <cedmo1@netzero.net> wrote:
>>>>>>
>>>>>>Anyone with ideas...I've been running Paris on 98SE for years, just
> last
>>>>>night
>>>>>>I go to open a project and get 2 error messages " I/O modules not
>>>>>>available
>>>>>>in this configuration....bla, bla" I have had this before when I
>>>>>>forget
>>>>>>to turn on the MEC, but it's on, I tried another cable...nada! any
>>>thoughts
>>>>>>? Thanks
>>>>>
>>>>
>>>
>>
>
|
|
|
|
Goto Forum:
Current Time: Sat Dec 21 19:48:37 PST 2024
Total time taken to generate the page: 0.00900 seconds
|
The PARIS Forums
Search
Help
Members
Register
Login
Home
