The PARIS Forums: PARIS: Main » Insert Funkiness

Home » The PARIS Forums » PARIS: Main » Insert Funkiness

Show: Today's Messages :: Polls :: Message Navigator

Insert Funkiness [message #106032]

Fri, 25 February 2011 19:20

Ted Gerber

Messages: 705
Registered: January 2009

Senior Member

Hi Folks - (whoever's still hangin' around)

I've been bussing out on the Master L/R to a Comp, and want to do the same from channel inserts.

No problem getting the signal out and back, but when I have "stereo" tracks - mono L & R for a drumbuss for instance - the image is messed up. Almost as if the phase is not quite inverted. This is even when using the same physical outs and ins from the MEC cards as when I'm inserting in the Master, which works fine, and preserves the stereo image.

Is this a known bug that I've missed?

Any help would be appreciated,

Ted

Report message to a moderator

Re: Insert Funkiness [message #106033 is a reply to message #106032]

Fri, 25 February 2011 19:53

lance

Messages: 47
Registered: December 2008
Location: Hamilton / Trenton / Prin...

Member

Hey Ted, Just a thought. If you haven't already tried this;
Zoom in on the LR files to sample level and see if they are 100%
lined up.

Report message to a moderator

Re: Insert Funkiness [message #106035 is a reply to message #106033]

Sat, 26 February 2011 19:23

Ted Gerber

Messages: 705
Registered: January 2009

Senior Member

Can't check right now, but if there's a problem to do with alignment, I would hear it regardless of whether I'm trying to send out to external inserts on each channel wouldn't I?

Also, if the 2 channels in question are the only ones in the project, then the lining up would be an issue when I am inserting on the master out as well right?

Thanks

Ted

Report message to a moderator

Re: Insert Funkiness [message #106037 is a reply to message #106035]

Sun, 27 February 2011 02:33

dnafe

Messages: 390
Registered: February 2009

Senior Member

Okay...really dumb question time...have you checked your cabling...all you need is one cabled wired incorrectly.

Report message to a moderator

Re: Insert Funkiness [message #106039 is a reply to message #106037]

Sun, 27 February 2011 07:05

Ted Gerber

Messages: 705
Registered: January 2009

Senior Member

Thanks Don -

The thing is I also use these same in/out connections on the MEC cards for the Master Insert (not trying to at the same time of course) and the stereo image is preserved with no problem. It's only when sending audio out of two channel inserts that are side by side. In other words, there is no actual physical change between the two scenarios, just the software routing inside of PARIS that's different.

SO:

Insert Main L & R to MEC 8out 1 & 2 and back = no problem
Insert Channels x/y to MEC 8out 1 & 2 and back = stereo image problem

?

Report message to a moderator

Re: Insert Funkiness [message #106040 is a reply to message #106039]

Sun, 27 February 2011 17:02

dnafe

Messages: 390
Registered: February 2009

Senior Member

Well if the cables are the same then there are only three possibilities

1) something inside your outboard gear is out of whack

2) Something inside the MEC and/or 8 out card is out of whack

3) Something in the software is out of whack

Dumb Q time again...

If you move the tracks to channels 3&4 and route out there do you get the same results?

Have you tried routing through the AUX send to an analogue output?

Are you using an 8 out card or just the MEC's 4 outs - if you're just using the MEC's 4 outs can you try using the 8 out card?

Hope this starts to narrow down the possibilities

Report message to a moderator

Re: Insert Funkiness [message #106041 is a reply to message #106040]

Sun, 27 February 2011 19:06

Ted Gerber

Messages: 705
Registered: January 2009

Senior Member

Thanks Don -

Yeah I'll try the changing to the Aux. Just to reiterate, the cables and connections remain the same whether I'm sending out from the Insert of the channel strips, or the insert of the global strip. It's the same cables from the same physical outs and ins of the 8out/8in card. I just re-patch in the Patch Bay window, leaving the actual cables in the same position.

I've checked phase invert etc on the channel strips too.

I'll check again to see if there's anything else I'm missing in software...

Ted

Report message to a moderator

Re: Insert Funkiness [message #106042 is a reply to message #106041]

Mon, 28 February 2011 05:41

dnafe

Messages: 390
Registered: February 2009

Senior Member

Interesting.

Report message to a moderator

Previous Topic:	Adding a Genx6 = better sound?
Next Topic:	Anyone heard from Kerry G?

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Fri Jun 13 17:40:41 PDT 2025

Total time taken to generate the page: 0.02121 seconds