The PARIS Forums


Home » The PARIS Forums » PARIS: Main » New pc for Paris at 21 (Problem with Memory Manager in w10?)
- New pc for Paris at 21 [message #109568] Mon, 05 November 2018 08:34 Go to next message
lastlaf51 is currently offline  lastlaf51   
Messages: 21
Registered: September 2014
Location: Norway
Junior Member
A question for Mike Audet:
In a response on the ASIO driver thread you talked about a
Memory manager problem in w10, and you were searching for answers to several questions. Did you ever get answers (satisfactory or otherwise) from M$oft? Should I have w7x64 or w10x64 in the new pc?
Thanks for your continued support for the Paris community Smile
- Re: New pc for Paris at 21 [message #109571 is a reply to message #109568] Tue, 11 December 2018 18:37 Go to previous messageGo to next message
mikeaudet   CANADA
Messages: 477
Registered: February 2009
Location: Canada
Senior Member
Hi lastlaf51,

I'm sorry that this response has taken so long. I've gone back to school, and it's been hectic.

The short answer is that I'm not sure.

The original post came from Vincent Burel at VB-Audio. He noted that any non-locked memory could cause long delays under Windows 10 as compared to Windows 7. The PARIS ASIO uses locked buffers anyway. This was supposed to be fixed in the spring update, but I could never get a confirmation one way or the other. I'm not seeing any problems on my system, even at 32 sample buffer sizes.

I did notice that there was something off under Windows 10 in terms of thread priorities. I recently found some undocumented Windows functions, and using them to boost the thread priority of the main buffer switch thread is working out perfectly. Windows 10 now works just like Windows 7 as far as the PARIS ASIO is concerned.

Windows 7 goes out of support in just over a year. In my view, it doesn't make sense to do a new Windows 7 build now given that you will just have to upgrade in twelve and a half months anyway if you want to be able to go online. That's just my take on things. Windows 10 is having more than it's share of issues lately, but I'm not having any problems on the Spring update.

I just made some changes to the ASIO control panel about a week ago. I'm going to test them tomorrow. My last exam was last night. If everything works, I just have to remove a bit of debugging code, and it's done. The change was so that +4/-10 expansion card settings will follow the expansion card, not the bank. So, if you have two 8 in cards, with a mix of +4 and -10 gear plugged into them, you'll be able to switch between them and the driver will load the right level settings automatically. It's not a big thing, but I though it was worthwhile. I also changed the C16 mode so that it is saved per ASIO host. So, if you save the C16 as Mackie HUI in Pro Tools 12 and also save it as Reaper OSC in Reaper, the driver will just load the right one by detecting the host.

It's really just little things at this point.

I did have to increase the output latency by 64 samples (as compared to the 4.15 ms I reported before, not compared to the old 32 bit ASIO driver), unfortunately. higher index outputs were being garbled at the lower setting.

That's all the news for now. I haven't been posting, but I've been working on the driver every chance I get.

All the best!

Mike


- Re: New pc for Paris at 21 [message #109577 is a reply to message #109571] Thu, 13 December 2018 11:15 Go to previous messageGo to next message
lastlaf51 is currently offline  lastlaf51   
Messages: 21
Registered: September 2014
Location: Norway
Junior Member
Hi Mike,
Thanks for the response, and new ASIO progress report.
And we see, as always, that "Release First-Repair Later" is as tried and true as it gets...they continue to release new versions that are, by definition, flawed and under-documented. And folks with your particular skill-set will continue on where the rubber meets the road.
No reason to expect any change there, unless someone figures out
how to sneak in and hack their dna a little Wink
- Re: New pc for Paris at 21 [message #109578 is a reply to message #109577] Thu, 13 December 2018 12:47 Go to previous message
mikeaudet   CANADA
Messages: 477
Registered: February 2009
Location: Canada
Senior Member
The bugs in the fall update are pretty unsettling. I got a notification that an update was ready, and I froze with fear. I postponed it. You couldn't pay me to use Windows 10 home and have these updates forced on me when they first come out.
Previous Topic: Paris recording+playback: linear or compression?
Next Topic: Merry Christmas!
Goto Forum:
  


Current Time: Sat Dec 14 16:47:22 PST 2024

Total time taken to generate the page: 0.01164 seconds