Home » The PARIS Forums » PARIS: Main » When recording w/both MECs, How do you bring up both mixers?
|
|
|
|
|
|
|
|
|
|
| Re: When recording w/both MECs, How do you bring up both mixers? [message #97079 is a reply to message #97065] |
Wed, 19 March 2008 08:54   |
Kim W
Messages: 165
Registered: July 2006
|
Senior Member |
|
|
Steve.
If you are running two EDS's, do yourself a favour and get a
second monitor for your rig. (the bigger the better..)
A 22" widescreen will do nicely, as you can see all 16 channels
of the submix, plus a few aux's, without scrolling.
Or pick up a 19" CRT (often found
on the kerb these days..) and run it at 1600x1200.
Kim
"Steve Cox" <stevec1@charter.net> wrote:
>
>"Make sense"? Not the windows thing, because I am on a Mac, but the submix
>button did. I just gotta make sure that I can record and view 24 simultanious
>tracks.
>
>"Don Nafe" <dnafe@magma.ca> wrote:
>>You can also toggle between submixes using the C16...hold down the submix
>
>>button then hit 1 or 2...then when you hit M, the active submix mixer window
>
>>will pop up
>>
>>I also use the task bar (in windows) to click on the mixer I want to view
>>
>>Make sense?
>>
>>Don
>>
>>
>>"rick" <parnell68@hotmail.com> wrote in message
>>news:e4l1u3dpcaeopd1vq28pafgb9jh741stb2@4ax.com...
>>> On 19 Mar 2008 13:05:39 +1000, "Steve Cox" <stevec1@charter.net>
>>> wrote:
>>>
>>>>
>>>>I am still trying to configure this thing. If you hit apple and M you
>get
>>>>the mixer. How will you be able to see both? Remember I am running 2
MECs
>>>>and need to record on 24 tracks at the same time.
>>>>Steve
>>>
>>> assuming it's the same on a mac as pc you can access the second mec by
>>> clicking on it in the project window.
>>>
>>
>>
>
|
|
|
|
| Re: When recording w/both MECs, How do you bring up both mixers? [message #97080 is a reply to message #97079] |
Wed, 19 March 2008 09:03 |
Stevehwan
Messages: 207
Registered: January 2006
|
Senior Member |
|
|
Can't run 2 monitors. All the slots are taken up w/EDS cards, but I do have
a 19" and visual is good. Moreso need the configuration correct.
"Kim W." <no@way.com> wrote:
>
>Steve.
>If you are running two EDS's, do yourself a favour and get a
>second monitor for your rig. (the bigger the better..)
>A 22" widescreen will do nicely, as you can see all 16 channels
>of the submix, plus a few aux's, without scrolling.
>Or pick up a 19" CRT (often found
>on the kerb these days..) and run it at 1600x1200.
>
>Kim
>
>"Steve Cox" <stevec1@charter.net> wrote:
>>
>>"Make sense"? Not the windows thing, because I am on a Mac, but the submix
>>button did. I just gotta make sure that I can record and view 24 simultanious
>>tracks.
>>
>>"Don Nafe" <dnafe@magma.ca> wrote:
>>>You can also toggle between submixes using the C16...hold down the submix
>>
>>>button then hit 1 or 2...then when you hit M, the active submix mixer
window
>>
>>>will pop up
>>>
>>>I also use the task bar (in windows) to click on the mixer I want to view
>>>
>>>Make sense?
>>>
>>>Don
>>>
>>>
>>>"rick" <parnell68@hotmail.com> wrote in message
>>>news:e4l1u3dpcaeopd1vq28pafgb9jh741stb2@4ax.com...
>>>> On 19 Mar 2008 13:05:39 +1000, "Steve Cox" <stevec1@charter.net>
>>>> wrote:
>>>>
>>>>>
>>>>>I am still trying to configure this thing. If you hit apple and M you
>>get
>>>>>the mixer. How will you be able to see both? Remember I am running 2
>MECs
>>>>>and need to record on 24 tracks at the same time.
>>>>>Steve
>>>>
>>>> assuming it's the same on a mac as pc you can access the second mec
by
>>>> clicking on it in the project window.
>>>>
>>>
>>>
>>
>
|
|
|
|
| Re: When recording w/both MECs, How do you bring up both mixers? [message #97082 is a reply to message #97080] |
Wed, 19 March 2008 09:33 |
Kim W
Messages: 165
Registered: July 2006
|
Senior Member |
|
|
I'm not familiar with macs, but any recent low rent graphics
card has two outputs. Can't you swap the existing card with
one of these?
If not, your only option is to toggle between mixers by bringing
up the project window, (press "p"), and click on the "M" button
corresponding to the submix you wish to view.
Unfortunately the Paris windows are fixed in size, due to the
fact that they are "hand drawn" bitmaps. You cannot shrink
them in size like you can with most other applications,
you can only increase screen resolution to allow more info to
be displayed.
Therefore, I cannot see how you can view 24 channels on one
monitor unless you use the Mini Mixer, as suggested by another
poster.
Kim
The only solution is to increase your desktop size, or reduce the
number of visible channels in each submix if you wish to see more
than one submix.
"Steve Cox" <stevec1@charter.net> wrote:
>
>Can't run 2 monitors. All the slots are taken up w/EDS cards, but I do have
>a 19" and visual is good. Moreso need the configuration correct.
>
>"Kim W." <no@way.com> wrote:
>>
>>Steve.
>>If you are running two EDS's, do yourself a favour and get a
>>second monitor for your rig. (the bigger the better..)
>>A 22" widescreen will do nicely, as you can see all 16 channels
>>of the submix, plus a few aux's, without scrolling.
>>Or pick up a 19" CRT (often found
>>on the kerb these days..) and run it at 1600x1200.
>>
>>Kim
>>
>>"Steve Cox" <stevec1@charter.net> wrote:
>>>
>>>"Make sense"? Not the windows thing, because I am on a Mac, but the submix
>>>button did. I just gotta make sure that I can record and view 24 simultanious
>>>tracks.
>>>
>>>"Don Nafe" <dnafe@magma.ca> wrote:
>>>>You can also toggle between submixes using the C16...hold down the submix
>>>
>>>>button then hit 1 or 2...then when you hit M, the active submix mixer
>window
>>>
>>>>will pop up
>>>>
>>>>I also use the task bar (in windows) to click on the mixer I want to
view
>>>>
>>>>Make sense?
>>>>
>>>>Don
>>>>
>>>>
>>>>"rick" <parnell68@hotmail.com> wrote in message
>>>>news:e4l1u3dpcaeopd1vq28pafgb9jh741stb2@4ax.com...
>>>>> On 19 Mar 2008 13:05:39 +1000, "Steve Cox" <stevec1@charter.net>
>>>>> wrote:
>>>>>
>>>>>>
>>>>>>I am still trying to configure this thing. If you hit apple and M you
>>>get
>>>>>>the mixer. How will you be able to see both? Remember I am running
2
>>MECs
>>>>>>and need to record on 24 tracks at the same time.
>>>>>>Steve
>>>>>
>>>>> assuming it's the same on a mac as pc you can access the second mec
>by
>>>>> clicking on it in the project window.
>>>>>
>>>>
>>>>
>>>
>>
>
|
|
|
|
| Re: When recording w/both MECs, How do you bring up both mixers? [message #97085 is a reply to message #97082] |
Wed, 19 March 2008 09:47 |
Kim W
Messages: 165
Registered: July 2006
|
Senior Member |
|
|
.....Having said that, you COULD concievably set up two mixer
views, one above the other, by minimising what is shown in each
submix.
I.E. get rid of the faders, aux sends, and/or inserts.
Set up a view that only shows what you need, and see if it will
fit on half the screen.
Then do the same for the second submix, and arrange the two, one above the
other.
Maybe I'm missing the point of your post, as I just jumped
into this thread without checking the last few days.
Good Luck
"Kim W." <no@way.com> wrote:
>
>I'm not familiar with macs, but any recent low rent graphics
>card has two outputs. Can't you swap the existing card with
>one of these?
>If not, your only option is to toggle between mixers by bringing
>up the project window, (press "p"), and click on the "M" button
>corresponding to the submix you wish to view.
>Unfortunately the Paris windows are fixed in size, due to the
>fact that they are "hand drawn" bitmaps. You cannot shrink
>them in size like you can with most other applications,
>you can only increase screen resolution to allow more info to
>be displayed.
>Therefore, I cannot see how you can view 24 channels on one
>monitor unless you use the Mini Mixer, as suggested by another
>poster.
>
>Kim
>
>The only solution is to increase your desktop size, or reduce the
>number of visible channels in each submix if you wish to see more
>than one submix.
>
>"Steve Cox" <stevec1@charter.net> wrote:
>>
>>Can't run 2 monitors. All the slots are taken up w/EDS cards, but I do
have
>>a 19" and visual is good. Moreso need the configuration correct.
>>
>>"Kim W." <no@way.com> wrote:
>>>
>>>Steve.
>>>If you are running two EDS's, do yourself a favour and get a
>>>second monitor for your rig. (the bigger the better..)
>>>A 22" widescreen will do nicely, as you can see all 16 channels
>>>of the submix, plus a few aux's, without scrolling.
>>>Or pick up a 19" CRT (often found
>>>on the kerb these days..) and run it at 1600x1200.
>>>
>>>Kim
>>>
>>>"Steve Cox" <stevec1@charter.net> wrote:
>>>>
>>>>"Make sense"? Not the windows thing, because I am on a Mac, but the submix
>>>>button did. I just gotta make sure that I can record and view 24 simultanious
>>>>tracks.
>>>>
>>>>"Don Nafe" <dnafe@magma.ca> wrote:
>>>>>You can also toggle between submixes using the C16...hold down the submix
>>>>
>>>>>button then hit 1 or 2...then when you hit M, the active submix mixer
>>window
>>>>
>>>>>will pop up
>>>>>
>>>>>I also use the task bar (in windows) to click on the mixer I want to
>view
>>>>>
>>>>>Make sense?
>>>>>
>>>>>Don
>>>>>
>>>>>
>>>>>"rick" <parnell68@hotmail.com> wrote in message
>>>>>news:e4l1u3dpcaeopd1vq28pafgb9jh741stb2@4ax.com...
>>>>>> On 19 Mar 2008 13:05:39 +1000, "Steve Cox" <stevec1@charter.net>
>>>>>> wrote:
>>>>>>
>>>>>>>
>>>>>>>I am still trying to configure this thing. If you hit apple and M
you
>>>>get
>>>>>>>the mixer. How will you be able to see both? Remember I am running
>2
>>>MECs
>>>>>>>and need to record on 24 tracks at the same time.
>>>>>>>Steve
>>>>>>
>>>>>> assuming it's the same on a mac as pc you can access the second mec
>>by
>>>>>> clicking on it in the project window.
>>>>>>
>>>>>
>>>>>
>>>>
>>>
>>
>
|
|
|
|
| Re: When recording w/both MECs, How do you bring up both mixers? [message #97098 is a reply to message #97085] |
Wed, 19 March 2008 13:50 |
Stevehwan
Messages: 207
Registered: January 2006
|
Senior Member |
|
|
I was responding to someone recommending that I view with 2 monitors. No problem
Kim, you coo, you coo.....
"Kim W." <no@way.com> wrote:>
>....Having said that, you COULD concievably set up two mixer
>views, one above the other, by minimising what is shown in each
>submix.
>I.E. get rid of the faders, aux sends, and/or inserts.
>Set up a view that only shows what you need, and see if it will
>fit on half the screen.
>Then do the same for the second submix, and arrange the two, one above the
>other.
>Maybe I'm missing the point of your post, as I just jumped
>into this thread without checking the last few days.
>Good Luck
>
>
>
>"Kim W." <no@way.com> wrote:
>>
>>I'm not familiar with macs, but any recent low rent graphics
>>card has two outputs. Can't you swap the existing card with
>>one of these?
>>If not, your only option is to toggle between mixers by bringing
>>up the project window, (press "p"), and click on the "M" button
>>corresponding to the submix you wish to view.
>>Unfortunately the Paris windows are fixed in size, due to the
>>fact that they are "hand drawn" bitmaps. You cannot shrink
>>them in size like you can with most other applications,
>>you can only increase screen resolution to allow more info to
>>be displayed.
>>Therefore, I cannot see how you can view 24 channels on one
>>monitor unless you use the Mini Mixer, as suggested by another
>>poster.
>>
>>Kim
>>
>>The only solution is to increase your desktop size, or reduce the
>>number of visible channels in each submix if you wish to see more
>>than one submix.
>>
>>"Steve Cox" <stevec1@charter.net> wrote:
>>>
>>>Can't run 2 monitors. All the slots are taken up w/EDS cards, but I do
>have
>>>a 19" and visual is good. Moreso need the configuration correct.
>>>
>>>"Kim W." <no@way.com> wrote:
>>>>
>>>>Steve.
>>>>If you are running two EDS's, do yourself a favour and get a
>>>>second monitor for your rig. (the bigger the better..)
>>>>A 22" widescreen will do nicely, as you can see all 16 channels
>>>>of the submix, plus a few aux's, without scrolling.
>>>>Or pick up a 19" CRT (often found
>>>>on the kerb these days..) and run it at 1600x1200.
>>>>
>>>>Kim
>>>>
>>>>"Steve Cox" <stevec1@charter.net> wrote:
>>>>>
>>>>>"Make sense"? Not the windows thing, because I am on a Mac, but the
submix
>>>>>button did. I just gotta make sure that I can record and view 24 simultanious
>>>>>tracks.
>>>>>
>>>>>"Don Nafe" <dnafe@magma.ca> wrote:
>>>>>>You can also toggle between submixes using the C16...hold down the
submix
>>>>>
>>>>>>button then hit 1 or 2...then when you hit M, the active submix mixer
>>>window
>>>>>
>>>>>>will pop up
>>>>>>
>>>>>>I also use the task bar (in windows) to click on the mixer I want to
>>view
>>>>>>
>>>>>>Make sense?
>>>>>>
>>>>>>Don
>>>>>>
>>>>>>
>>>>>>"rick" <parnell68@hotmail.com> wrote in message
>>>>>>news:e4l1u3dpcaeopd1vq28pafgb9jh741stb2@4ax.com...
>>>>>>> On 19 Mar 2008 13:05:39 +1000, "Steve Cox" <stevec1@charter.net>
>>>>>>> wrote:
>>>>>>>
>>>>>>>>
>>>>>>>>I am still trying to configure this thing. If you hit apple and M
>you
>>>>>get
>>>>>>>>the mixer. How will you be able to see both? Remember I am running
>>2
>>>>MECs
>>>>>>>>and need to record on 24 tracks at the same time.
>>>>>>>>Steve
>>>>>>>
>>>>>>> assuming it's the same on a mac as pc you can access the second mec
>>>by
>>>>>>> clicking on it in the project window.
>>>>>>>
>>>>>>
>>>>>>
>>>>>
>>>>
>>>
>>
>
|
|
|
|
Goto Forum:
Current Time: Tue Dec 24 13:07:22 PST 2024
Total time taken to generate the page: 0.01012 seconds
|
The PARIS Forums
Search
Help
Members
Register
Login
Home
