The PARIS Forums


Home » The PARIS Forums » PARIS: Main » Help - I think I pooched my EDS card
- Help - I think I pooched my EDS card [message #90563] Tue, 25 September 2007 20:40 Go to next message
Ted Gerber is currently offline  Ted Gerber   
Messages: 705
Registered: January 2009
Senior Member
Hi Folks-

I need some hardware advice. I think I've wrecked my EDS input connector.
We're recording and editing in different locations, and I've been lugging
my
Paris rig all over the place. Tonight, while in a hurry to set up for tracking,
I forced the EDS/Mec connector cable into the EDS card at a bad angle, and
broke
a couple of pins. No problem, I have a spare and used it. No luck. When Paris
boots,
it now cannot find the Mec.

A closer look at the female input connector on the EDS card, shows some damage

too.

My question is, can this component be replaced as a separate item by any
computer
repair type, or is it not removable, and therefore I'll need to send the
card away?

Any help appreciated, we're wanting to keep moving on this.

Peace,

Ted
- Re: Help - I think I pooched my EDS card [message #90567 is a reply to message #90563] Tue, 25 September 2007 22:39 Go to previous messageGo to next message
Nei is currently offline  Nei
Messages: 108
Registered: November 2006
Senior Member
"Ted Gerber" <tedgerber@rogers.com> wrote:
>A closer look at the female input connector on the EDS card, shows some
damage
>
>too.
>
>My question is, can this component be replaced as a separate item by any
>computer
>repair type, or is it not removable, and therefore I'll need
>to send the card away?
>
>Any help appreciated, we're wanting to keep moving on this.

Probably a dumb question, but have you tried prying out the card
connectors a tad? It might be that you just crushed or
collapsed them a bit.

Neil
- Re: Help - I think I pooched my EDS card [message #90585 is a reply to message #90567] Wed, 26 September 2007 04:38 Go to previous messageGo to next message
Ted Gerber is currently offline  Ted Gerber   
Messages: 705
Registered: January 2009
Senior Member
Thanks Neil-

Yeah we took the card out and put it under the magnifying glass. The 2 bottom
left input holes seem fine, and we can't find the broken tips anywhere. As
for
the broken male end, I have another back up cable that's fne, and it's not

working either.

Ted




"Neil" <OIUOI@OIU.com> wrote:
>
>"Ted Gerber" <tedgerber@rogers.com> wrote:
>>A closer look at the female input connector on the EDS card, shows some
>damage
>>
>>too.
>>
>>My question is, can this component be replaced as a separate item by any
>>computer
>>repair type, or is it not removable, and therefore I'll need
>>to send the card away?
>>
>>Any help appreciated, we're wanting to keep moving on this.
>
>Probably a dumb question, but have you tried prying out the card
>connectors a tad? It might be that you just crushed or
>collapsed them a bit.
>
>Neil
- Re: Help - I think I pooched my EDS card [message #90587 is a reply to message #90585] Wed, 26 September 2007 05:43 Go to previous message
Ted Gerber is currently offline  Ted Gerber   
Messages: 705
Registered: January 2009
Senior Member
Took the EDS card out again- and with light behind the plug, I can see
it's clear that one of the holes is blocked (prolly with the broken tip off
the
male input).

Does anyone know if this component is soldered to the Card itself? Hoping
to be able to replace it if I can't extricate the pin tip...

Thanks,

Ted


"Ted Gerber" <tedgerber@rogers.com> wrote:
>
>Thanks Neil-
>
>Yeah we took the card out and put it under the magnifying glass. The 2 bottom
>left input holes seem fine, and we can't find the broken tips anywhere.
As
>for
>the broken male end, I have another back up cable that's fne, and it's not
>
>working either.
>
>Ted
>
>
>
>
>"Neil" <OIUOI@OIU.com> wrote:
>>
>>"Ted Gerber" <tedgerber@rogers.com> wrote:
>>>A closer look at the female input connector on the EDS card, shows some
>>damage
>>>
>>>too.
>>>
>>>My question is, can this component be replaced as a separate item by any
>>>computer
>>>repair type, or is it not removable, and therefore I'll need
>>>to send the card away?
>>>
>>>Any help appreciated, we're wanting to keep moving on this.
>>
>>Probably a dumb question, but have you tried prying out the card
>>connectors a tad? It might be that you just crushed or
>>collapsed them a bit.
>>
>>Neil
>
Previous Topic: http://www.woot.com/
Next Topic: Win98 users, have a question
Goto Forum:
  


Current Time: Sat Dec 14 22:54:39 PST 2024

Total time taken to generate the page: 0.01802 seconds