The PARIS Forums: PARIS: Main » "Interface 2" with 2 EDS's

Home » The PARIS Forums » PARIS: Main » "Interface 2" with 2 EDS's - Paris won't initialize

Show: Today's Messages :: Polls :: Message Navigator

"Interface 2" with 2 EDS's - Paris won't initialize [message #66769]

Sat, 15 April 2006 05:50

Chris Griffiths

Messages: 7
Registered: April 2006

Junior Member

Hi All,

Does anybody know if you have to have a 442 or a MEC to run multiple EDS
cards? I only have an "Interface 2" - 2 in's and 2 out's. With 2 EDSs Paris
gives the following error on launch - "No interface connected to master
card" - even though my interface is connected to the master card. All cables
are connected as per instructions.

Thanks,

Chris Griffiths.

P.S. Unfortunately I don't know anyone who still uses paris with a MEC
interface I can try (From Australia).

Report message to a moderator

Re: "Interface 2" with 2 EDS's - Paris won't initialize [message #66773 is a reply to message #66769]

Sat, 15 April 2006 08:15

chuck duffy
Messages: 453
Registered: July 2005

Senior Member

Hi Chris,

IF2s don't have sync capability, thus can't be used as the only interface
in a two card system. You will need 2 442s or 2mecs. 2 442s should be a
really cheap way to go.

Chuck

"Chris Griffiths" <cgriffo@aapt.net.au> wrote:
>Hi All,
>
>Does anybody know if you have to have a 442 or a MEC to run multiple EDS

>cards? I only have an "Interface 2" - 2 in's and 2 out's. With 2 EDSs Paris

>gives the following error on launch - "No interface connected to master

>card" - even though my interface is connected to the master card. All cables

>are connected as per instructions.
>
>Thanks,
>
>Chris Griffiths.
>
>P.S. Unfortunately I don't know anyone who still uses paris with a MEC
>interface I can try (From Australia).
>
>

Report message to a moderator

Re: "Interface 2" with 2 EDS's - Paris won't initialize [message #66779 is a reply to message #66773]

Sat, 15 April 2006 09:16

audioguy_editout_

Messages: 249
Registered: December 2005

Senior Member

Just to clarify, you would only "need" one 442 or MEC to get
a two card system operational... the second if you wanted to
be able to record to two subgroups at one time.

David.

chuck wrote:

> Hi Chris,
>
> IF2s don't have sync capability, thus can't be used as the only interface
> in a two card system. You will need 2 442s or 2mecs. 2 442s should be a
> really cheap way to go.
>
> Chuck
>
> "Chris Griffiths" <cgriffo@aapt.net.au> wrote:
>
>>Hi All,
>>
>>Does anybody know if you have to have a 442 or a MEC to run multiple EDS
>
>
>>cards? I only have an "Interface 2" - 2 in's and 2 out's. With 2 EDSs Paris
>
>
>>gives the following error on launch - "No interface connected to master
>
>
>>card" - even though my interface is connected to the master card. All cables
>
>
>>are connected as per instructions.
>>
>>Thanks,
>>
>>Chris Griffiths.
>>
>>P.S. Unfortunately I don't know anyone who still uses paris with a MEC
>>interface I can try (From Australia).
>>
>>
>
>

Report message to a moderator

Re: "Interface 2" with 2 EDS's - Paris won't initialize [message #66805 is a reply to message #66769]

Sat, 15 April 2006 15:08

Kim
Messages: 1246
Registered: October 2005

Senior Member

"Chris Griffiths" <cgriffo@aapt.net.au> wrote:
>P.S. Unfortunately I don't know anyone who still uses paris with a MEC
>interface I can try (From Australia).

I'm in Australia and still use Paris. In Northcote, in Melbourne. What city
are you in?

Though the other guys are right. With two cards you'll need a 442 or an MEC.
442's come up pretty cheap on the for sale site.

And you'll still be able to plug the Interface 2 into the system. There's
a plug in the MEC so that you can piggy back it on to the MEC (I assume the
442 has that as well? Andyone?)

Cheers,
Kim.

Report message to a moderator

Re: "Interface 2" with 2 EDS's - Paris won't initialize [message #66814 is a reply to message #66805]

Sat, 15 April 2006 15:58

Aaron Allen

Messages: 1988
Registered: May 2008

Senior Member

Correct, 442 has that option as well. I used one for years w/o any hassles.
AA

"Kim" <hiddensounds@hotmail.com> wrote in message news:44416ece$1@linux...
>
> "Chris Griffiths" <cgriffo@aapt.net.au> wrote:
>>P.S. Unfortunately I don't know anyone who still uses paris with a MEC
>>interface I can try (From Australia).
>
> I'm in Australia and still use Paris. In Northcote, in Melbourne. What
> city
> are you in?
>
> Though the other guys are right. With two cards you'll need a 442 or an
> MEC.
> 442's come up pretty cheap on the for sale site.
>
> And you'll still be able to plug the Interface 2 into the system. There's
> a plug in the MEC so that you can piggy back it on to the MEC (I assume
> the
> 442 has that as well? Andyone?)
>
> Cheers,
> Kim.

I choose Polesoft Lockspam to fight spam, and you?
http://www.polesoft.com/refer.html

Report message to a moderator

Re: "Interface 2" with 2 EDS's - Paris won't initialize [message #66840 is a reply to message #66805]

Sat, 15 April 2006 18:46

Chris Griffiths

Messages: 7
Registered: April 2006

Junior Member

Hi Kim,

I'm in Winston Hills, near Parramatta, Sydney. Thanks for your help.

Chris.

"Kim" <hiddensounds@hotmail.com> wrote in message news:44416ece$1@linux...
>
> "Chris Griffiths" <cgriffo@aapt.net.au> wrote:
>>P.S. Unfortunately I don't know anyone who still uses paris with a MEC
>>interface I can try (From Australia).
>
> I'm in Australia and still use Paris. In Northcote, in Melbourne. What
> city
> are you in?
>
> Though the other guys are right. With two cards you'll need a 442 or an
> MEC.
> 442's come up pretty cheap on the for sale site.
>
> And you'll still be able to plug the Interface 2 into the system. There's
> a plug in the MEC so that you can piggy back it on to the MEC (I assume
> the
> 442 has that as well? Andyone?)
>
> Cheers,
> Kim.

Report message to a moderator

THANKS GUYS! I also use Hammerfall/RME + Nuendo but prefer Paris for vocals. [message #66841 is a reply to message #66769]

Sat, 15 April 2006 19:04

Chris Griffiths

Messages: 7
Registered: April 2006

Junior Member

Thanks Guys,

I guess I'll have to buy a 442.

Just to fill you in, I also use a Hammerfall card with 3 RMEs for 24 ins and
outs (used with Nuendo or SX). But I still use Paris all the time. Why? I
use Paris for Vocal recordings and individual instruments and have done so
for years - even after getting the Hammerfall/RME system. I just find it
sounds better (warmer? hard to explain). All I wanted to do was get another
EDS card before they're too hard to get, I'm sick of updating virtual tracks
all the time.

Interestingly, my angle with clients lately, is that I use Paris because
it's a warmer, earthier converter. They seem to agree, and really go for
Paris as an almost "Retro" alternative. Believe it or not, it seems to be
cool to use Paris (especially with young bands) because it's getting old and
it's a bit rare. I've also started using my ASR-10 again! Clients think it's
cool - go figure!

Chris.

"Chris Griffiths" <cgriffo@aapt.net.au> wrote in message
news:4440eb8f@linux...
> Hi All,
>
> Does anybody know if you have to have a 442 or a MEC to run multiple EDS
> cards? I only have an "Interface 2" - 2 in's and 2 out's. With 2 EDSs
> Paris gives the following error on launch - "No interface connected to
> master card" - even though my interface is connected to the master card.
> All cables are connected as per instructions.
>
> Thanks,
>
> Chris Griffiths.
>
> P.S. Unfortunately I don't know anyone who still uses paris with a MEC
> interface I can try (From Australia).
>

Report message to a moderator

Re: "Interface 2" with 2 EDS's - Paris won't initialize [message #66843 is a reply to message #66805]

Sat, 15 April 2006 19:07

Martin Harrington

Messages: 560
Registered: September 2005

Senior Member

Chris is in Sydney, a mate of mine, but I can't help as I no longer have
Paris.
BTW, you should here some of the work Chris has achieved with Paris and 1
EDS card and an IF2.

Absolutely amazing.
--
Martin Harrington
www.lendanear-sound.com
"Kim" <hiddensounds@hotmail.com> wrote in message news:44416ece$1@linux...
>
> "Chris Griffiths" <cgriffo@aapt.net.au> wrote:
>>P.S. Unfortunately I don't know anyone who still uses paris with a MEC
>>interface I can try (From Australia).
>
> I'm in Australia and still use Paris. In Northcote, in Melbourne. What
> city
> are you in?
>
> Though the other guys are right. With two cards you'll need a 442 or an
> MEC.
> 442's come up pretty cheap on the for sale site.
>
> And you'll still be able to plug the Interface 2 into the system. There's
> a plug in the MEC so that you can piggy back it on to the MEC (I assume
> the
> 442 has that as well? Andyone?)
>
> Cheers,
> Kim.

Report message to a moderator

Re: "Interface 2" with 2 EDS's - Paris won't initialize [message #66844 is a reply to message #66843]

Sat, 15 April 2006 19:10

Kim
Messages: 1246
Registered: October 2005

Senior Member

Really? I'd love to hear.

Anyone know how I can get hold of some?

Cheers,
Kim.

"Martin Harrington" <lendan@bigpond.net.au> wrote:
>Chris is in Sydney, a mate of mine, but I can't help as I no longer have

>Paris.
>BTW, you should here some of the work Chris has achieved with Paris and
1
>EDS card and an IF2.
>
>Absolutely amazing.
>--
>Martin Harrington
>www.lendanear-sound.com
>"Kim" <hiddensounds@hotmail.com> wrote in message news:44416ece$1@linux...
>>
>> "Chris Griffiths" <cgriffo@aapt.net.au> wrote:
>>>P.S. Unfortunately I don't know anyone who still uses paris with a MEC
>>>interface I can try (From Australia).
>>
>> I'm in Australia and still use Paris. In Northcote, in Melbourne. What

>> city
>> are you in?
>>
>> Though the other guys are right. With two cards you'll need a 442 or an

>> MEC.
>> 442's come up pretty cheap on the for sale site.
>>
>> And you'll still be able to plug the Interface 2 into the system. There's
>> a plug in the MEC so that you can piggy back it on to the MEC (I assume

>> the
>> 442 has that as well? Andyone?)
>>
>> Cheers,
>> Kim.
>
>

Report message to a moderator

Re: "Interface 2" with 2 EDS's - Paris won't initialize [message #66862 is a reply to message #66844]

Sun, 16 April 2006 00:24

Martin Harrington

Messages: 560
Registered: September 2005

Senior Member

Talk to Chris
--
Martin Harrington
www.lendanear-sound.com

"Kim" <hiddensounds@hotmail.com> wrote in message news:4441a794$1@linux...
>
>
> Really? I'd love to hear.
>
> Anyone know how I can get hold of some?
>
> Cheers,
> Kim.
>
> "Martin Harrington" <lendan@bigpond.net.au> wrote:
>>Chris is in Sydney, a mate of mine, but I can't help as I no longer have
>
>>Paris.
>>BTW, you should here some of the work Chris has achieved with Paris and
> 1
>>EDS card and an IF2.
>>
>>Absolutely amazing.
>>--
>>Martin Harrington
>>www.lendanear-sound.com
>>"Kim" <hiddensounds@hotmail.com> wrote in message news:44416ece$1@linux...
>>>
>>> "Chris Griffiths" <cgriffo@aapt.net.au> wrote:
>>>>P.S. Unfortunately I don't know anyone who still uses paris with a MEC
>>>>interface I can try (From Australia).
>>>
>>> I'm in Australia and still use Paris. In Northcote, in Melbourne. What
>
>>> city
>>> are you in?
>>>
>>> Though the other guys are right. With two cards you'll need a 442 or an
>
>>> MEC.
>>> 442's come up pretty cheap on the for sale site.
>>>
>>> And you'll still be able to plug the Interface 2 into the system.
>>> There's
>>> a plug in the MEC so that you can piggy back it on to the MEC (I assume
>
>>> the
>>> 442 has that as well? Andyone?)
>>>
>>> Cheers,
>>> Kim.
>>
>>
>

Report message to a moderator

Previous Topic:	So donators, here she is. New UPS! :o) 260kb Attachment
Next Topic:	Planned Outage - 0:00 GMT

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Mon Dec 23 07:11:10 PST 2024

Total time taken to generate the page: 0.01987 seconds