Home » The PARIS Forums » PARIS: Main » Any Tascam 3200/4800 users here?
| Any Tascam 3200/4800 users here? [message #78922] |
Wed, 24 January 2007 12:26  |
Jon Jiles
Messages: 90
Registered: November 2005
|
Member |
|
|
Hi,
Anyone here actually had any real hands on with this board/controller, especially
with Cubase 4? James got me intrigued but I have read that the build quolity
may be somewhat on cheesy side.
Thanks,
Jon
|
|
|
|
| Re: Any Tascam 3200/4800 users here? [message #78930 is a reply to message #78922] |
Wed, 24 January 2007 13:41  |
excelav
Messages: 2130
Registered: July 2005
Location: Metro Detroit
|
Senior Member |
|
|
Hey Jon!
Some of the guys on the DA7 NG have switched to the Tascam DM 32s. A customer
of mine also has one. The mixes from both source sound good. You should
always test drive before you buy. You have to like it. I would think twice
before buying a DM-24, the Mic pres were not so good, they had low head room.
If you use the DM-24 for line ins only, I think you'd be Ok. There was
an upgrade for the mic pres through Tascam, they may no longer be doing that.
I hear the DM manuals are terrible, you can go down load them. If you buy
one, make sure you have 30 full days to test it. Clear your planner for
test time. Read the manual in advance and go to the NG a lot before you
get it. Every once in awhile Tascam puts out a lemon, so you want to be
able to fully test what you buy from them. Unless they have changed their
policy, they only have a 90 day warranty!!!
James
"Jon Jiles" <snoid@sheboygan.com> wrote:
>
>Hi,
>
>Anyone here actually had any real hands on with this board/controller, especially
>with Cubase 4? James got me intrigued but I have read that the build quolity
>may be somewhat on cheesy side.
>
>Thanks,
>Jon
|
|
|
|
| Re: Any Tascam 3200/4800 users here? [message #78931 is a reply to message #78930] |
Wed, 24 January 2007 13:46 |
excelav
Messages: 2130
Registered: July 2005
Location: Metro Detroit
|
Senior Member |
|
|
By the way, the mic pres on the DM-32 and DM-48 are greatly improved and vary
usable. It was only the DM-24 that had the problems.
James
"James McCloskey" <excelsm@hotmail.com> wrote:
>
>Hey Jon!
>
>Some of the guys on the DA7 NG have switched to the Tascam DM 32s. A customer
>of mine also has one. The mixes from both source sound good. You should
>always test drive before you buy. You have to like it. I would think twice
>before buying a DM-24, the Mic pres were not so good, they had low head
room.
> If you use the DM-24 for line ins only, I think you'd be Ok. There was
>an upgrade for the mic pres through Tascam, they may no longer be doing
that.
>
>I hear the DM manuals are terrible, you can go down load them. If you buy
>one, make sure you have 30 full days to test it. Clear your planner for
>test time. Read the manual in advance and go to the NG a lot before you
>get it. Every once in awhile Tascam puts out a lemon, so you want to be
>able to fully test what you buy from them. Unless they have changed their
>policy, they only have a 90 day warranty!!!
>
>James
>
>"Jon Jiles" <snoid@sheboygan.com> wrote:
>>
>>Hi,
>>
>>Anyone here actually had any real hands on with this board/controller,
especially
>>with Cubase 4? James got me intrigued but I have read that the build quolity
>>may be somewhat on cheesy side.
>>
>>Thanks,
>>Jon
>
|
|
|
|
|
|
| Re: Any Tascam 3200/4800 users here? [message #79056 is a reply to message #78931] |
Sat, 27 January 2007 00:16 |
Jon Jiles
Messages: 90
Registered: November 2005
|
Member |
|
|
Thanks for all the info James!
How do they stack up against the Yamaha boards? (O2r96v2 and the DM1000v2,etc)
Also, Cubase implementation will be a key factor if I move from Paris. I
will consider the Yamaha boards too (used though due to price) because of
the Yammy/Steinberg connection and better Cubase implementation I would suppose.
The Tascam boards do seem like a very good value though... especially if
they don't break and are not horribly non-intuitive.
Thanks again,
Jon
"James McCloskey" <excelsm@hotmail.com> wrote:
>
>By the way, the mic pres on the DM-32 and DM-48 are greatly improved and
vary
>usable. It was only the DM-24 that had the problems.
>
>James
>
>"James McCloskey" <excelsm@hotmail.com> wrote:
>>
>>Hey Jon!
>>
>>Some of the guys on the DA7 NG have switched to the Tascam DM 32s. A customer
>>of mine also has one. The mixes from both source sound good. You should
>>always test drive before you buy. You have to like it. I would think
twice
>>before buying a DM-24, the Mic pres were not so good, they had low head
>room.
>> If you use the DM-24 for line ins only, I think you'd be Ok. There was
>>an upgrade for the mic pres through Tascam, they may no longer be doing
>that.
>>
>>I hear the DM manuals are terrible, you can go down load them. If you
buy
>>one, make sure you have 30 full days to test it. Clear your planner for
>>test time. Read the manual in advance and go to the NG a lot before you
>>get it. Every once in awhile Tascam puts out a lemon, so you want to be
>>able to fully test what you buy from them. Unless they have changed their
>>policy, they only have a 90 day warranty!!!
>>
>>James
>>
>>"Jon Jiles" <snoid@sheboygan.com> wrote:
>>>
>>>Hi,
>>>
>>>Anyone here actually had any real hands on with this board/controller,
>especially
>>>with Cubase 4? James got me intrigued but I have read that the build quolity
>>>may be somewhat on cheesy side.
>>>
>>>Thanks,
>>>Jon
>>
>
|
|
|
|
| Re: Any Tascam 3200/4800 users here? [message #79077 is a reply to message #79056] |
Sat, 27 January 2007 13:05 |
excelav
Messages: 2130
Registered: July 2005
Location: Metro Detroit
|
Senior Member |
|
|
Hi Jon!
Sorry, I can't compare the Tascam to the Yamaha, I have no real experience
and I've never compared them side by side. I used a Yamaha 02r on a regular
basis in the past, but that won't help here. So what I'm going to say is
unqualified. There are some guys here that have used Tascam control surfaces
with Cubase, so maybe someone could chime in. Tascam has been at it a while,
so I would think their implementation of Cubase control would be good by
now???
Your best bet is to go to all the Tascam NGs and do the research there.
You can start here: http://www.tascamforums.com/
Also check out Mike Ofca reports on the Tascam DM-3200 on the DA7 NG at:
da7.com. Mike has first hand experience with the DM-32. While your at it
check out his web site where he is selling his CD and watch the video, there
is some really nice guitar playing.
You can hear and kind of see the DM-320 in the back ground on the video.
http://www.mikeofca.com/
His studio
http://www.innovationstudios.net/
If some one was going to give me the Tascam or the Yamaha, I would take the
Yamaha. However, I would buy the Tascam, because I know I could get great
sounding work done on it at a reasonable price.
I posted the info about the Tascam because I think it fits in to that 5 to
6K range LaMont was talking about. As LaMont put it, throw a DM 4800 or
two in a Argosy console and clients would be impressed. I think they would
be also impressed with the sound, from what I'm hearing. I'm thinking that
it might be my next move in a year or so. I think it would be a good solution,
especially for the price.
James
"Jon Jiles" <nanaheyhey@no.com> wrote:
>
>Thanks for all the info James!
>
>How do they stack up against the Yamaha boards? (O2r96v2 and the DM1000v2,etc)
>Also, Cubase implementation will be a key factor if I move from Paris. I
>will consider the Yamaha boards too (used though due to price) because of
>the Yammy/Steinberg connection and better Cubase implementation I would
suppose.
>The Tascam boards do seem like a very good value though... especially if
>they don't break and are not horribly non-intuitive.
>
>Thanks again,
>Jon
>
>"James McCloskey" <excelsm@hotmail.com> wrote:
>>
>>By the way, the mic pres on the DM-32 and DM-48 are greatly improved and
>vary
>>usable. It was only the DM-24 that had the problems.
>>
>>James
>>
>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>
>>>Hey Jon!
>>>
>>>Some of the guys on the DA7 NG have switched to the Tascam DM 32s. A
customer
>>>of mine also has one. The mixes from both source sound good. You should
>>>always test drive before you buy. You have to like it. I would think
>twice
>>>before buying a DM-24, the Mic pres were not so good, they had low head
>>room.
>>> If you use the DM-24 for line ins only, I think you'd be Ok. There was
>>>an upgrade for the mic pres through Tascam, they may no longer be doing
>>that.
>>>
>>>I hear the DM manuals are terrible, you can go down load them. If you
>buy
>>>one, make sure you have 30 full days to test it. Clear your planner for
>>>test time. Read the manual in advance and go to the NG a lot before you
>>>get it. Every once in awhile Tascam puts out a lemon, so you want to
be
>>>able to fully test what you buy from them. Unless they have changed their
>>>policy, they only have a 90 day warranty!!!
>>>
>>>James
>>>
>>>"Jon Jiles" <snoid@sheboygan.com> wrote:
>>>>
>>>>Hi,
>>>>
>>>>Anyone here actually had any real hands on with this board/controller,
>>especially
>>>>with Cubase 4? James got me intrigued but I have read that the build
quolity
>>>>may be somewhat on cheesy side.
>>>>
>>>>Thanks,
>>>>Jon
>>>
>>
>
|
|
|
|
| Re: Any Tascam 3200/4800 users here? [message #79079 is a reply to message #79077] |
Sat, 27 January 2007 13:45 |
excelav
Messages: 2130
Registered: July 2005
Location: Metro Detroit
|
Senior Member |
|
|
Jon, when you get to da7.com do a search for Tascam DM-3200, there you can
read Mike Ofca's first impressions on the DM-3200.
Here is the first thing Mike mixed on the DM-3200 out of the box.
http://innovationstudios.net/da7/pinwheel3_m.mp3
He made some adjustments, here's the remix.
http://www.innovationstudios.net/da7/pinwheel5_m.mp3
James
"James McCloskey" <excelsm@hotmail.com> wrote:
>
>Hi Jon!
>
>Sorry, I can't compare the Tascam to the Yamaha, I have no real experience
>and I've never compared them side by side. I used a Yamaha 02r on a regular
>basis in the past, but that won't help here. So what I'm going to say is
>unqualified. There are some guys here that have used Tascam control surfaces
>with Cubase, so maybe someone could chime in. Tascam has been at it a while,
>so I would think their implementation of Cubase control would be good by
>now???
>
>Your best bet is to go to all the Tascam NGs and do the research there.
>You can start here: http://www.tascamforums.com/
>
>Also check out Mike Ofca reports on the Tascam DM-3200 on the DA7 NG at:
>da7.com. Mike has first hand experience with the DM-32. While your at
it
>check out his web site where he is selling his CD and watch the video, there
>is some really nice guitar playing.
>
>You can hear and kind of see the DM-320 in the back ground on the video.
>http://www.mikeofca.com/
>
>His studio
>http://www.innovationstudios.net/
>
>If some one was going to give me the Tascam or the Yamaha, I would take
the
>Yamaha. However, I would buy the Tascam, because I know I could get great
>sounding work done on it at a reasonable price.
>
>I posted the info about the Tascam because I think it fits in to that 5
to
>6K range LaMont was talking about. As LaMont put it, throw a DM 4800 or
>two in a Argosy console and clients would be impressed. I think they would
>be also impressed with the sound, from what I'm hearing. I'm thinking that
>it might be my next move in a year or so. I think it would be a good solution,
>especially for the price.
>
>James
>
>"Jon Jiles" <nanaheyhey@no.com> wrote:
>>
>>Thanks for all the info James!
>>
>>How do they stack up against the Yamaha boards? (O2r96v2 and the DM1000v2,etc)
>>Also, Cubase implementation will be a key factor if I move from Paris.
I
>>will consider the Yamaha boards too (used though due to price) because
of
>>the Yammy/Steinberg connection and better Cubase implementation I would
>suppose.
>>The Tascam boards do seem like a very good value though... especially if
>>they don't break and are not horribly non-intuitive.
>>
>>Thanks again,
>>Jon
>>
>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>
>>>By the way, the mic pres on the DM-32 and DM-48 are greatly improved and
>>vary
>>>usable. It was only the DM-24 that had the problems.
>>>
>>>James
>>>
>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>
>>>>Hey Jon!
>>>>
>>>>Some of the guys on the DA7 NG have switched to the Tascam DM 32s. A
>customer
>>>>of mine also has one. The mixes from both source sound good. You should
>>>>always test drive before you buy. You have to like it. I would think
>>twice
>>>>before buying a DM-24, the Mic pres were not so good, they had low head
>>>room.
>>>> If you use the DM-24 for line ins only, I think you'd be Ok. There
was
>>>>an upgrade for the mic pres through Tascam, they may no longer be doing
>>>that.
>>>>
>>>>I hear the DM manuals are terrible, you can go down load them. If you
>>buy
>>>>one, make sure you have 30 full days to test it. Clear your planner
for
>>>>test time. Read the manual in advance and go to the NG a lot before
you
>>>>get it. Every once in awhile Tascam puts out a lemon, so you want to
>be
>>>>able to fully test what you buy from them. Unless they have changed
their
>>>>policy, they only have a 90 day warranty!!!
>>>>
>>>>James
>>>>
>>>>"Jon Jiles" <snoid@sheboygan.com> wrote:
>>>>>
>>>>>Hi,
>>>>>
>>>>>Anyone here actually had any real hands on with this board/controller,
>>>especially
>>>>>with Cubase 4? James got me intrigued but I have read that the build
>quolity
>>>>>may be somewhat on cheesy side.
>>>>>
>>>>>Thanks,
>>>>>Jon
>>>>
>>>
>>
>
|
|
|
|
| Re: Any Tascam 3200/4800 users here? [message #79086 is a reply to message #79079] |
Sat, 27 January 2007 16:09 |
Nil
Messages: 245
Registered: March 2007
|
Senior Member |
|
|
I think I like the first mix better - the 2nd mix has some
extra fizz on the guitar that it really doesn't need. Vocals
sound better on the first, too - not sure what the difference
is... a little bit of ambient somethingorother that's not there
on the 2nd, maybe? Dunno.
They both sound damn good.
Neil
"James McCloskey" <excelsm@hotmail.com> wrote:
>
>Jon, when you get to da7.com do a search for Tascam DM-3200, there you can
>read Mike Ofca's first impressions on the DM-3200.
>
>Here is the first thing Mike mixed on the DM-3200 out of the box.
>
>http://innovationstudios.net/da7/pinwheel3_m.mp3
>
>He made some adjustments, here's the remix.
>http://www.innovationstudios.net/da7/pinwheel5_m.mp3
>
>James
>
>"James McCloskey" <excelsm@hotmail.com> wrote:
>>
>>Hi Jon!
>>
>>Sorry, I can't compare the Tascam to the Yamaha, I have no real experience
>>and I've never compared them side by side. I used a Yamaha 02r on a regular
>>basis in the past, but that won't help here. So what I'm going to say
is
>>unqualified. There are some guys here that have used Tascam control surfaces
>>with Cubase, so maybe someone could chime in. Tascam has been at it a
while,
>>so I would think their implementation of Cubase control would be good by
>>now???
>>
>>Your best bet is to go to all the Tascam NGs and do the research there.
>
>>You can start here: http://www.tascamforums.com/
>>
>>Also check out Mike Ofca reports on the Tascam DM-3200 on the DA7 NG at:
>>da7.com. Mike has first hand experience with the DM-32. While your at
>it
>>check out his web site where he is selling his CD and watch the video,
there
>>is some really nice guitar playing.
>>
>>You can hear and kind of see the DM-320 in the back ground on the video.
>>http://www.mikeofca.com/
>>
>>His studio
>>http://www.innovationstudios.net/
>>
>>If some one was going to give me the Tascam or the Yamaha, I would take
>the
>>Yamaha. However, I would buy the Tascam, because I know I could get great
>>sounding work done on it at a reasonable price.
>>
>>I posted the info about the Tascam because I think it fits in to that 5
>to
>>6K range LaMont was talking about. As LaMont put it, throw a DM 4800 or
>>two in a Argosy console and clients would be impressed. I think they would
>>be also impressed with the sound, from what I'm hearing. I'm thinking
that
>>it might be my next move in a year or so. I think it would be a good solution,
>>especially for the price.
>>
>>James
>>
>>"Jon Jiles" <nanaheyhey@no.com> wrote:
>>>
>>>Thanks for all the info James!
>>>
>>>How do they stack up against the Yamaha boards? (O2r96v2 and the DM1000v2,etc)
>>>Also, Cubase implementation will be a key factor if I move from Paris.
>I
>>>will consider the Yamaha boards too (used though due to price) because
>of
>>>the Yammy/Steinberg connection and better Cubase implementation I would
>>suppose.
>>>The Tascam boards do seem like a very good value though... especially
if
>>>they don't break and are not horribly non-intuitive.
>>>
>>>Thanks again,
>>>Jon
>>>
>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>
>>>>By the way, the mic pres on the DM-32 and DM-48 are greatly improved
and
>>>vary
>>>>usable. It was only the DM-24 that had the problems.
>>>>
>>>>James
>>>>
>>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>>
>>>>>Hey Jon!
>>>>>
>>>>>Some of the guys on the DA7 NG have switched to the Tascam DM 32s.
A
>>customer
>>>>>of mine also has one. The mixes from both source sound good. You should
>>>>>always test drive before you buy. You have to like it. I would think
>>>twice
>>>>>before buying a DM-24, the Mic pres were not so good, they had low head
>>>>room.
>>>>> If you use the DM-24 for line ins only, I think you'd be Ok. There
>was
>>>>>an upgrade for the mic pres through Tascam, they may no longer be doing
>>>>that.
>>>>>
>>>>>I hear the DM manuals are terrible, you can go down load them. If you
>>>buy
>>>>>one, make sure you have 30 full days to test it. Clear your planner
>for
>>>>>test time. Read the manual in advance and go to the NG a lot before
>you
>>>>>get it. Every once in awhile Tascam puts out a lemon, so you want to
>>be
>>>>>able to fully test what you buy from them. Unless they have changed
>their
>>>>>policy, they only have a 90 day warranty!!!
>>>>>
>>>>>James
>>>>>
>>>>>"Jon Jiles" <snoid@sheboygan.com> wrote:
>>>>>>
>>>>>>Hi,
>>>>>>
>>>>>>Anyone here actually had any real hands on with this board/controller,
>>>>especially
>>>>>>with Cubase 4? James got me intrigued but I have read that the build
>>quolity
>>>>>>may be somewhat on cheesy side.
>>>>>>
>>>>>>Thanks,
>>>>>>Jon
>>>>>
>>>>
>>>
>>
>
|
|
|
|
| Re: Any Tascam 3200/4800 users here?...YES!!! [message #79099 is a reply to message #79056] |
Sat, 27 January 2007 23:44 |
LaMont
Messages: 828
Registered: October 2005
|
Senior Member |
|
|
Hi Jon, I can chime in here on this question.
I often work at a local studio http://www.lamourrecording.com/
which has (2) Yamaha's DM2000. I can't speak highly enough of these powerful
beast.
Great feel, 96 channels @ 96K
Pro Tools, Neundo/Cubase/Sonar/Logic Controller
Nice Comps/EQs on every channel
(8) SPX-1000's DSP processors (REVerbs, Delays, Chorus.etc)
Some of the sweetest (24) Mic pres you'll find
All in a foot print that keeps the Engineer/Operator right in
front of the mix..There's a ton more features..
I had a chance (2years) ago to take the then Tascam 3200 for week session
spin. Due to the fact that no body in our area had a O2r/96, we rented
the tascam.. Man, to my ears and others, the Tascam delivers the goods. I
would have to say that the Tascam 3200 sonics was more "thick" than the DM2000.
Different converters and clocks.. But, we mananged to get thru a sesion without
opening the manual!!
You're not going to do that with the Yammys.. he 3200 had full eq and dynamics
on every channel as well as I think 4 DSP processors for Verbs and dleays
chorus FX.. The verbs were the star of this board. The algo's were from TC!!
the verb masters. Man, these verbs sounded like our TC 3000 ..really!!. The
Eqs were usuable as are the Comps/Lim..We click on the DAW controller layer
button, scrolled to the DAW template (Pro Tools)..Boom!! "Houston We have
Controll".. That easy.. We had transport, channel faders and Master faders
and edit scroll.. To be honest, we probable had more functions,but like I
stated earlier, we had not read the manual..
Oh well.
Like I told James, I'm looking seriously @ the DM4800 X2 for my Home studio..To
host Both Nuendo & Pro Tools...AND yes, Liek BrianT does in Houston, Paris
will be used a he master summing mixer/recorder..
The DM3200/4800 can't be beat in their price range. They have the sound,
looks, and product maturity. Tascam knew they had a winner with the DM24,then
knocked the ball out of the park with the DM3200, and now DM 4800..
Now that it's official that Mackie has dropped the Ball with the DXB(20K
Plus), now selling are drastic discounts. The DXB is a one sweet sounding
board as well. At 9k it competes very well with Yammys O2r/96..But, (2) x
DM4800 @ around is just as and (imo) more potent ..AND dropped in a cool
Argosy, BAMM!..
http://www.argosyconsole.com/dm3200.htm
"Jon Jiles" <nanaheyhey@no.com> wrote:
>
>Thanks for all the info James!
>
>How do they stack up against the Yamaha boards? (O2r96v2 and the DM1000v2,etc)
>Also, Cubase implementation will be a key factor if I move from Paris. I
>will consider the Yamaha boards too (used though due to price) because of
>the Yammy/Steinberg connection and better Cubase implementation I would
suppose.
>The Tascam boards do seem like a very good value though... especially if
>they don't break and are not horribly non-intuitive.
>
>Thanks again,
>Jon
>
>"James McCloskey" <excelsm@hotmail.com> wrote:
>>
>>By the way, the mic pres on the DM-32 and DM-48 are greatly improved and
>vary
>>usable. It was only the DM-24 that had the problems.
>>
>>James
>>
>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>
>>>Hey Jon!
>>>
>>>Some of the guys on the DA7 NG have switched to the Tascam DM 32s. A
customer
>>>of mine also has one. The mixes from both source sound good. You should
>>>always test drive before you buy. You have to like it. I would think
>twice
>>>before buying a DM-24, the Mic pres were not so good, they had low head
>>room.
>>> If you use the DM-24 for line ins only, I think you'd be Ok. There was
>>>an upgrade for the mic pres through Tascam, they may no longer be doing
>>that.
>>>
>>>I hear the DM manuals are terrible, you can go down load them. If you
>buy
>>>one, make sure you have 30 full days to test it. Clear your planner for
>>>test time. Read the manual in advance and go to the NG a lot before you
>>>get it. Every once in awhile Tascam puts out a lemon, so you want to
be
>>>able to fully test what you buy from them. Unless they have changed their
>>>policy, they only have a 90 day warranty!!!
>>>
>>>James
>>>
>>>"Jon Jiles" <snoid@sheboygan.com> wrote:
>>>>
>>>>Hi,
>>>>
>>>>Anyone here actually had any real hands on with this board/controller,
>>especially
>>>>with Cubase 4? James got me intrigued but I have read that the build
quolity
>>>>may be somewhat on cheesy side.
>>>>
>>>>Thanks,
>>>>Jon
>>>
>>
>
|
|
|
|
| Re: Any Tascam 3200/4800 users here? [message #79119 is a reply to message #79086] |
Sun, 28 January 2007 11:39 |
excelav
Messages: 2130
Registered: July 2005
Location: Metro Detroit
|
Senior Member |
|
|
Hey Neil! Did you watch Mike's video? If you didn't, you should check it
out.
James
"Neil" <IUOIU@OIU.com> wrote:
>
>I think I like the first mix better - the 2nd mix has some
>extra fizz on the guitar that it really doesn't need. Vocals
>sound better on the first, too - not sure what the difference
>is... a little bit of ambient somethingorother that's not there
>on the 2nd, maybe? Dunno.
>
>They both sound damn good.
>
>Neil
>
>
>
>"James McCloskey" <excelsm@hotmail.com> wrote:
>>
>>Jon, when you get to da7.com do a search for Tascam DM-3200, there you
can
>>read Mike Ofca's first impressions on the DM-3200.
>>
>>Here is the first thing Mike mixed on the DM-3200 out of the box.
>>
>>http://innovationstudios.net/da7/pinwheel3_m.mp3
>>
>>He made some adjustments, here's the remix.
>>http://www.innovationstudios.net/da7/pinwheel5_m.mp3
>>
>>James
>>
>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>
>>>Hi Jon!
>>>
>>>Sorry, I can't compare the Tascam to the Yamaha, I have no real experience
>>>and I've never compared them side by side. I used a Yamaha 02r on a regular
>>>basis in the past, but that won't help here. So what I'm going to say
>is
>>>unqualified. There are some guys here that have used Tascam control surfaces
>>>with Cubase, so maybe someone could chime in. Tascam has been at it a
>while,
>>>so I would think their implementation of Cubase control would be good
by
>>>now???
>>>
>>>Your best bet is to go to all the Tascam NGs and do the research there.
>>
>>>You can start here: http://www.tascamforums.com/
>>>
>>>Also check out Mike Ofca reports on the Tascam DM-3200 on the DA7 NG at:
>>>da7.com. Mike has first hand experience with the DM-32. While your at
>>it
>>>check out his web site where he is selling his CD and watch the video,
>there
>>>is some really nice guitar playing.
>>>
>>>You can hear and kind of see the DM-320 in the back ground on the video.
>>>http://www.mikeofca.com/
>>>
>>>His studio
>>>http://www.innovationstudios.net/
>>>
>>>If some one was going to give me the Tascam or the Yamaha, I would take
>>the
>>>Yamaha. However, I would buy the Tascam, because I know I could get great
>>>sounding work done on it at a reasonable price.
>>>
>>>I posted the info about the Tascam because I think it fits in to that
5
>>to
>>>6K range LaMont was talking about. As LaMont put it, throw a DM 4800
or
>>>two in a Argosy console and clients would be impressed. I think they
would
>>>be also impressed with the sound, from what I'm hearing. I'm thinking
>that
>>>it might be my next move in a year or so. I think it would be a good
solution,
>>>especially for the price.
>>>
>>>James
>>>
>>>"Jon Jiles" <nanaheyhey@no.com> wrote:
>>>>
>>>>Thanks for all the info James!
>>>>
>>>>How do they stack up against the Yamaha boards? (O2r96v2 and the DM1000v2,etc)
>>>>Also, Cubase implementation will be a key factor if I move from Paris.
>>I
>>>>will consider the Yamaha boards too (used though due to price) because
>>of
>>>>the Yammy/Steinberg connection and better Cubase implementation I would
>>>suppose.
>>>>The Tascam boards do seem like a very good value though... especially
>if
>>>>they don't break and are not horribly non-intuitive.
>>>>
>>>>Thanks again,
>>>>Jon
>>>>
>>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>>
>>>>>By the way, the mic pres on the DM-32 and DM-48 are greatly improved
>and
>>>>vary
>>>>>usable. It was only the DM-24 that had the problems.
>>>>>
>>>>>James
>>>>>
>>>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>>>
>>>>>>Hey Jon!
>>>>>>
>>>>>>Some of the guys on the DA7 NG have switched to the Tascam DM 32s.
>A
>>>customer
>>>>>>of mine also has one. The mixes from both source sound good. You
should
>>>>>>always test drive before you buy. You have to like it. I would think
>>>>twice
>>>>>>before buying a DM-24, the Mic pres were not so good, they had low
head
>>>>>room.
>>>>>> If you use the DM-24 for line ins only, I think you'd be Ok. There
>>was
>>>>>>an upgrade for the mic pres through Tascam, they may no longer be doing
>>>>>that.
>>>>>>
>>>>>>I hear the DM manuals are terrible, you can go down load them. If
you
>>>>buy
>>>>>>one, make sure you have 30 full days to test it. Clear your planner
>>for
>>>>>>test time. Read the manual in advance and go to the NG a lot before
>>you
>>>>>>get it. Every once in awhile Tascam puts out a lemon, so you want
to
>>>be
>>>>>>able to fully test what you buy from them. Unless they have changed
>>their
>>>>>>policy, they only have a 90 day warranty!!!
>>>>>>
>>>>>>James
>>>>>>
>>>>>>"Jon Jiles" <snoid@sheboygan.com> wrote:
>>>>>>>
>>>>>>>Hi,
>>>>>>>
>>>>>>>Anyone here actually had any real hands on with this board/controller,
>>>>>especially
>>>>>>>with Cubase 4? James got me intrigued but I have read that the build
>>>quolity
>>>>>>>may be somewhat on cheesy side.
>>>>>>>
>>>>>>>Thanks,
>>>>>>>Jon
>>>>>>
>>>>>
>>>>
>>>
>>
>
|
|
|
|
| Re: Any Tascam 3200/4800 users here?...YES!!! [message #79168 is a reply to message #79099] |
Mon, 29 January 2007 10:28 |
Jon Jiles
Messages: 90
Registered: November 2005
|
Member |
|
|
Wow!!!!
That's a pretty ringing endorsement LaMont!!!!
I'm definitely leaning towards the 3200 and Cubase 4. The only client in
my studio is me and I'm really just trying to get to a simpler workflow ,for
the songwriting end of things, and still achieve quality results at the end
of the process.
Can you eplain to me in a little more detail how you (and apparently BT)
would be/are using Paris as the master summing mixer/recorder in this scenario?
I've currently got Cubase SX3 lightpiped into Paris via a RME 9652 ( a mini-Deej
set-up if, you will) but being a guy who only gets to work on my stuff in
the evenings after work or on the weekends, the opportunity for confusion
in such a kludge ridden set-up doesn't lend itself to the creative workflow.
That's why Cubase and a nice board/control surface appeals. My big dilemma
though is that I still absolutely love the way Paris sounds.
Anyway, thanks a ton for the input, greatly appreciated! I've got much to
consider.
Cheers,
jon
"LaMont" <jjdpro@ameritech.net> wrote:
>
>Hi Jon, I can chime in here on this question.
>
>I often work at a local studio http://www.lamourrecording.com/
>which has (2) Yamaha's DM2000. I can't speak highly enough of these powerful
>beast.
>
>Great feel, 96 channels @ 96K
>Pro Tools, Neundo/Cubase/Sonar/Logic Controller
>Nice Comps/EQs on every channel
>(8) SPX-1000's DSP processors (REVerbs, Delays, Chorus.etc)
>Some of the sweetest (24) Mic pres you'll find
>All in a foot print that keeps the Engineer/Operator right in
>front of the mix..There's a ton more features..
>
>I had a chance (2years) ago to take the then Tascam 3200 for week session
>spin. Due to the fact that no body in our area had a O2r/96, we rented
>the tascam.. Man, to my ears and others, the Tascam delivers the goods.
I
>would have to say that the Tascam 3200 sonics was more "thick" than the
DM2000.
>Different converters and clocks.. But, we mananged to get thru a sesion
without
>opening the manual!!
>You're not going to do that with the Yammys.. he 3200 had full eq and dynamics
>on every channel as well as I think 4 DSP processors for Verbs and dleays
>chorus FX.. The verbs were the star of this board. The algo's were from
TC!!
>the verb masters. Man, these verbs sounded like our TC 3000 ..really!!.
The
>Eqs were usuable as are the Comps/Lim..We click on the DAW controller layer
>button, scrolled to the DAW template (Pro Tools)..Boom!! "Houston We have
>Controll".. That easy.. We had transport, channel faders and Master faders
>and edit scroll.. To be honest, we probable had more functions,but like
I
>stated earlier, we had not read the manual..
>Oh well.
>
>Like I told James, I'm looking seriously @ the DM4800 X2 for my Home studio..To
>host Both Nuendo & Pro Tools...AND yes, Liek BrianT does in Houston, Paris
>will be used a he master summing mixer/recorder..
>
>The DM3200/4800 can't be beat in their price range. They have the sound,
>looks, and product maturity. Tascam knew they had a winner with the DM24,then
>knocked the ball out of the park with the DM3200, and now DM 4800..
>
>Now that it's official that Mackie has dropped the Ball with the DXB(20K
>Plus), now selling are drastic discounts. The DXB is a one sweet sounding
>board as well. At 9k it competes very well with Yammys O2r/96..But, (2)
x
>DM4800 @ around is just as and (imo) more potent ..AND dropped in a cool
>Argosy, BAMM!..
>
>http://www.argosyconsole.com/dm3200.htm
>
>
>
>"Jon Jiles" <nanaheyhey@no.com> wrote:
>>
>>Thanks for all the info James!
>>
>>How do they stack up against the Yamaha boards? (O2r96v2 and the DM1000v2,etc)
>>Also, Cubase implementation will be a key factor if I move from Paris.
I
>>will consider the Yamaha boards too (used though due to price) because
of
>>the Yammy/Steinberg connection and better Cubase implementation I would
>suppose.
>>The Tascam boards do seem like a very good value though... especially if
>>they don't break and are not horribly non-intuitive.
>>
>>Thanks again,
>>Jon
>>
>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>
>>>By the way, the mic pres on the DM-32 and DM-48 are greatly improved and
>>vary
>>>usable. It was only the DM-24 that had the problems.
>>>
>>>James
>>>
>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>
>>>>Hey Jon!
>>>>
>>>>Some of the guys on the DA7 NG have switched to the Tascam DM 32s. A
>customer
>>>>of mine also has one. The mixes from both source sound good. You should
>>>>always test drive before you buy. You have to like it. I would think
>>twice
>>>>before buying a DM-24, the Mic pres were not so good, they had low head
>>>room.
>>>> If you use the DM-24 for line ins only, I think you'd be Ok. There
was
>>>>an upgrade for the mic pres through Tascam, they may no longer be doing
>>>that.
>>>>
>>>>I hear the DM manuals are terrible, you can go down load them. If you
>>buy
>>>>one, make sure you have 30 full days to test it. Clear your planner
for
>>>>test time. Read the manual in advance and go to the NG a lot before
you
>>>>get it. Every once in awhile Tascam puts out a lemon, so you want to
>be
>>>>able to fully test what you buy from them. Unless they have changed
their
>>>>policy, they only have a 90 day warranty!!!
>>>>
>>>>James
>>>>
>>>>"Jon Jiles" <snoid@sheboygan.com> wrote:
>>>>>
>>>>>Hi,
>>>>>
>>>>>Anyone here actually had any real hands on with this board/controller,
>>>especially
>>>>>with Cubase 4? James got me intrigued but I have read that the build
>quolity
>>>>>may be somewhat on cheesy side.
>>>>>
>>>>>Thanks,
>>>>>Jon
>>>>
>>>
>>
>
|
|
|
|
| Re: Any Tascam 3200/4800 users here?...YES!!! [message #79177 is a reply to message #79168] |
Mon, 29 January 2007 13:19 |
LaMont
Messages: 828
Registered: October 2005
|
Senior Member |
|
|
Hey Jon,
Trust me, the marriage of the Tascam 3200 & Cuabse 4 is a match made in heaven.
You will not miss the Paris sound.
However to not throw away your Paris investment(s), instead of summing out
of the 3200..you can...
Another way.. 3200 out via SP/Dif. into Paris Mec/442 SP/dif..for just a
stereo sum .. Again, good sound.
3200 master (analog outs) into Paris MEC/442.. 24bit(input Card)..then 24bit
out card..to master or internal bounce..
You can't loose either way you go.. Grat choice!!
P.S. Put into an Argosy!!! :)
take care.
- 3200 out (Adat x 2) 16 lightpipes stems into MEC (with 2 adat cards)..
For stem mixing. Very cool.. Very good sound. and provides a means of Matering
within Paris.
"Jon Jiles" <nojij@yahoo.com> wrote:
>
>Wow!!!!
>
>That's a pretty ringing endorsement LaMont!!!!
>
>I'm definitely leaning towards the 3200 and Cubase 4. The only client in
>my studio is me and I'm really just trying to get to a simpler workflow
,for
>the songwriting end of things, and still achieve quality results at the
end
>of the process.
>
>Can you eplain to me in a little more detail how you (and apparently BT)
>would be/are using Paris as the master summing mixer/recorder in this scenario?
>
>I've currently got Cubase SX3 lightpiped into Paris via a RME 9652 ( a mini-Deej
>set-up if, you will) but being a guy who only gets to work on my stuff in
>the evenings after work or on the weekends, the opportunity for confusion
>in such a kludge ridden set-up doesn't lend itself to the creative workflow.
>That's why Cubase and a nice board/control surface appeals. My big dilemma
>though is that I still absolutely love the way Paris sounds.
>
>Anyway, thanks a ton for the input, greatly appreciated! I've got much to
>consider.
>
>Cheers,
>jon
>
>
>"LaMont" <jjdpro@ameritech.net> wrote:
>>
>>Hi Jon, I can chime in here on this question.
>>
>>I often work at a local studio http://www.lamourrecording.com/
>>which has (2) Yamaha's DM2000. I can't speak highly enough of these powerful
>>beast.
>>
>>Great feel, 96 channels @ 96K
>>Pro Tools, Neundo/Cubase/Sonar/Logic Controller
>>Nice Comps/EQs on every channel
>>(8) SPX-1000's DSP processors (REVerbs, Delays, Chorus.etc)
>>Some of the sweetest (24) Mic pres you'll find
>>All in a foot print that keeps the Engineer/Operator right in
>>front of the mix..There's a ton more features..
>>
>>I had a chance (2years) ago to take the then Tascam 3200 for week session
>>spin. Due to the fact that no body in our area had a O2r/96, we rented
>>the tascam.. Man, to my ears and others, the Tascam delivers the goods.
>I
>>would have to say that the Tascam 3200 sonics was more "thick" than the
>DM2000.
>>Different converters and clocks.. But, we mananged to get thru a sesion
>without
>>opening the manual!!
>>You're not going to do that with the Yammys.. he 3200 had full eq and dynamics
>>on every channel as well as I think 4 DSP processors for Verbs and dleays
>>chorus FX.. The verbs were the star of this board. The algo's were from
>TC!!
>>the verb masters. Man, these verbs sounded like our TC 3000 ..really!!.
>The
>>Eqs were usuable as are the Comps/Lim..We click on the DAW controller layer
>>button, scrolled to the DAW template (Pro Tools)..Boom!! "Houston We have
>>Controll".. That easy.. We had transport, channel faders and Master faders
>>and edit scroll.. To be honest, we probable had more functions,but like
>I
>>stated earlier, we had not read the manual..
>>Oh well.
>>
>>Like I told James, I'm looking seriously @ the DM4800 X2 for my Home studio..To
>>host Both Nuendo & Pro Tools...AND yes, Liek BrianT does in Houston, Paris
>>will be used a he master summing mixer/recorder..
>>
>>The DM3200/4800 can't be beat in their price range. They have the sound,
>>looks, and product maturity. Tascam knew they had a winner with the DM24,then
>>knocked the ball out of the park with the DM3200, and now DM 4800..
>>
>>Now that it's official that Mackie has dropped the Ball with the DXB(20K
>>Plus), now selling are drastic discounts. The DXB is a one sweet sounding
>>board as well. At 9k it competes very well with Yammys O2r/96..But, (2)
>x
>>DM4800 @ around is just as and (imo) more potent ..AND dropped in a cool
>>Argosy, BAMM!..
>>
>>http://www.argosyconsole.com/dm3200.htm
>>
>>
>>
>>"Jon Jiles" <nanaheyhey@no.com> wrote:
>>>
>>>Thanks for all the info James!
>>>
>>>How do they stack up against the Yamaha boards? (O2r96v2 and the DM1000v2,etc)
>>>Also, Cubase implementation will be a key factor if I move from Paris.
>I
>>>will consider the Yamaha boards too (used though due to price) because
>of
>>>the Yammy/Steinberg connection and better Cubase implementation I would
>>suppose.
>>>The Tascam boards do seem like a very good value though... especially
if
>>>they don't break and are not horribly non-intuitive.
>>>
>>>Thanks again,
>>>Jon
>>>
>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>
>>>>By the way, the mic pres on the DM-32 and DM-48 are greatly improved
and
>>>vary
>>>>usable. It was only the DM-24 that had the problems.
>>>>
>>>>James
>>>>
>>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>>
>>>>>Hey Jon!
>>>>>
>>>>>Some of the guys on the DA7 NG have switched to the Tascam DM 32s.
A
>>customer
>>>>>of mine also has one. The mixes from both source sound good. You should
>>>>>always test drive before you buy. You have to like it. I would think
>>>twice
>>>>>before buying a DM-24, the Mic pres were not so good, they had low head
>>>>room.
>>>>> If you use the DM-24 for line ins only, I think you'd be Ok. There
>was
>>>>>an upgrade for the mic pres through Tascam, they may no longer be doing
>>>>that.
>>>>>
>>>>>I hear the DM manuals are terrible, you can go down load them. If you
>>>buy
>>>>>one, make sure you have 30 full days to test it. Clear your planner
>for
>>>>>test time. Read the manual in advance and go to the NG a lot before
>you
>>>>>get it. Every once in awhile Tascam puts out a lemon, so you want to
>>be
>>>>>able to fully test what you buy from them. Unless they have changed
>their
>>>>>policy, they only have a 90 day warranty!!!
>>>>>
>>>>>James
>>>>>
>>>>>"Jon Jiles" <snoid@sheboygan.com> wrote:
>>>>>>
>>>>>>Hi,
>>>>>>
>>>>>>Anyone here actually had any real hands on with this board/controller,
>>>>especially
>>>>>>with Cubase 4? James got me intrigued but I have read that the build
>>quolity
>>>>>>may be somewhat on cheesy side.
>>>>>>
>>>>>>Thanks,
>>>>>>Jon
>>>>>
>>>>
>>>
>>
>
|
|
|
|
| Re: Any Tascam 3200/4800 users here?...YES!!! [message #79180 is a reply to message #79177] |
Mon, 29 January 2007 13:23 |
excelav
Messages: 2130
Registered: July 2005
Location: Metro Detroit
|
Senior Member |
|
|
It should be noted that the 442 SP/DIF is only 20bit. The SP/DIF on the MEC
is 24bit.
James
"LaMont " <jjdpro@ameritech.net> wrote:
>
>Hey Jon,
>
>Trust me, the marriage of the Tascam 3200 & Cuabse 4 is a match made in
heaven.
>You will not miss the Paris sound.
>
>However to not throw away your Paris investment(s), instead of summing out
>of the 3200..you can...
>
>Another way.. 3200 out via SP/Dif. into Paris Mec/442 SP/dif..for just a
>stereo sum .. Again, good sound.
>
>3200 master (analog outs) into Paris MEC/442.. 24bit(input Card)..then 24bit
>out card..to master or internal bounce..
>
>You can't loose either way you go.. Grat choice!!
>P.S. Put into an Argosy!!! :)
>take care.
>
>- 3200 out (Adat x 2) 16 lightpipes stems into MEC (with 2 adat cards)..
>For stem mixing. Very cool.. Very good sound. and provides a means of Matering
>within Paris.
>
>"Jon Jiles" <nojij@yahoo.com> wrote:
>>
>>Wow!!!!
>>
>>That's a pretty ringing endorsement LaMont!!!!
>>
>>I'm definitely leaning towards the 3200 and Cubase 4. The only client in
>>my studio is me and I'm really just trying to get to a simpler workflow
>,for
>>the songwriting end of things, and still achieve quality results at the
>end
>>of the process.
>>
>>Can you eplain to me in a little more detail how you (and apparently BT)
>>would be/are using Paris as the master summing mixer/recorder in this scenario?
>>
>>I've currently got Cubase SX3 lightpiped into Paris via a RME 9652 ( a
mini-Deej
>>set-up if, you will) but being a guy who only gets to work on my stuff
in
>>the evenings after work or on the weekends, the opportunity for confusion
>>in such a kludge ridden set-up doesn't lend itself to the creative workflow.
>>That's why Cubase and a nice board/control surface appeals. My big dilemma
>>though is that I still absolutely love the way Paris sounds.
>>
>>Anyway, thanks a ton for the input, greatly appreciated! I've got much
to
>>consider.
>>
>>Cheers,
>>jon
>>
>>
>>"LaMont" <jjdpro@ameritech.net> wrote:
>>>
>>>Hi Jon, I can chime in here on this question.
>>>
>>>I often work at a local studio http://www.lamourrecording.com/
>>>which has (2) Yamaha's DM2000. I can't speak highly enough of these powerful
>>>beast.
>>>
>>>Great feel, 96 channels @ 96K
>>>Pro Tools, Neundo/Cubase/Sonar/Logic Controller
>>>Nice Comps/EQs on every channel
>>>(8) SPX-1000's DSP processors (REVerbs, Delays, Chorus.etc)
>>>Some of the sweetest (24) Mic pres you'll find
>>>All in a foot print that keeps the Engineer/Operator right in
>>>front of the mix..There's a ton more features..
>>>
>>>I had a chance (2years) ago to take the then Tascam 3200 for week session
>>>spin. Due to the fact that no body in our area had a O2r/96, we rented
>>>the tascam.. Man, to my ears and others, the Tascam delivers the goods.
>>I
>>>would have to say that the Tascam 3200 sonics was more "thick" than the
>>DM2000.
>>>Different converters and clocks.. But, we mananged to get thru a sesion
>>without
>>>opening the manual!!
>>>You're not going to do that with the Yammys.. he 3200 had full eq and
dynamics
>>>on every channel as well as I think 4 DSP processors for Verbs and dleays
>>>chorus FX.. The verbs were the star of this board. The algo's were from
>>TC!!
>>>the verb masters. Man, these verbs sounded like our TC 3000 ..really!!.
>>The
>>>Eqs were usuable as are the Comps/Lim..We click on the DAW controller
layer
>>>button, scrolled to the DAW template (Pro Tools)..Boom!! "Houston We have
>>>Controll".. That easy.. We had transport, channel faders and Master faders
>>>and edit scroll.. To be honest, we probable had more functions,but like
>>I
>>>stated earlier, we had not read the manual..
>>>Oh well.
>>>
>>>Like I told James, I'm looking seriously @ the DM4800 X2 for my Home studio..To
>>>host Both Nuendo & Pro Tools...AND yes, Liek BrianT does in Houston, Paris
>>>will be used a he master summing mixer/recorder..
>>>
>>>The DM3200/4800 can't be beat in their price range. They have the sound,
>>>looks, and product maturity. Tascam knew they had a winner with the DM24,then
>>>knocked the ball out of the park with the DM3200, and now DM 4800..
>>>
>>>Now that it's official that Mackie has dropped the Ball with the DXB(20K
>>>Plus), now selling are drastic discounts. The DXB is a one sweet sounding
>>>board as well. At 9k it competes very well with Yammys O2r/96..But, (2)
>>x
>>>DM4800 @ around is just as and (imo) more potent ..AND dropped in a cool
>>>Argosy, BAMM!..
>>>
>>>http://www.argosyconsole.com/dm3200.htm
>>>
>>>
>>>
>>>"Jon Jiles" <nanaheyhey@no.com> wrote:
>>>>
>>>>Thanks for all the info James!
>>>>
>>>>How do they stack up against the Yamaha boards? (O2r96v2 and the DM1000v2,etc)
>>>>Also, Cubase implementation will be a key factor if I move from Paris.
>>I
>>>>will consider the Yamaha boards too (used though due to price) because
>>of
>>>>the Yammy/Steinberg connection and better Cubase implementation I would
>>>suppose.
>>>>The Tascam boards do seem like a very good value though... especially
>if
>>>>they don't break and are not horribly non-intuitive.
>>>>
>>>>Thanks again,
>>>>Jon
>>>>
>>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>>
>>>>>By the way, the mic pres on the DM-32 and DM-48 are greatly improved
>and
>>>>vary
>>>>>usable. It was only the DM-24 that had the problems.
>>>>>
>>>>>James
>>>>>
>>>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>>>
>>>>>>Hey Jon!
>>>>>>
>>>>>>Some of the guys on the DA7 NG have switched to the Tascam DM 32s.
>A
>>>customer
>>>>>>of mine also has one. The mixes from both source sound good. You
should
>>>>>>always test drive before you buy. You have to like it. I would think
>>>>twice
>>>>>>before buying a DM-24, the Mic pres were not so good, they had low
head
>>>>>room.
>>>>>> If you use the DM-24 for line ins only, I think you'd be Ok. There
>>was
>>>>>>an upgrade for the mic pres through Tascam, they may no longer be doing
>>>>>that.
>>>>>>
>>>>>>I hear the DM manuals are terrible, you can go down load them. If
you
>>>>buy
>>>>>>one, make sure you have 30 full days to test it. Clear your planner
>>for
>>>>>>test time. Read the manual in advance and go to the NG a lot before
>>you
>>>>>>get it. Every once in awhile Tascam puts out a lemon, so you want
to
>>>be
>>>>>>able to fully test what you buy from them. Unless they have changed
>>their
>>>>>>policy, they only have a 90 day warranty!!!
>>>>>>
>>>>>>James
>>>>>>
>>>>>>"Jon Jiles" <snoid@sheboygan.com> wrote:
>>>>>>>
>>>>>>>Hi,
>>>>>>>
>>>>>>>Anyone here actually had any real hands on with this board/controller,
>>>>>especially
>>>>>>>with Cubase 4? James got me intrigued but I have read that the build
>>>quolity
>>>>>>>may be somewhat on cheesy side.
>>>>>>>
>>>>>>>Thanks,
>>>>>>>Jon
>>>>>>
>>>>>
>>>>
>>>
>>
>
|
|
|
|
| Re: Any Tascam 3200/4800 users here?...YES!!! [message #79184 is a reply to message #79177] |
Mon, 29 January 2007 13:34 |
Jon Jiles
Messages: 90
Registered: November 2005
|
Member |
|
|
Thanks LaMont -
I had considered keeping some of my Paris rig to use as a glorified mastering
deck. Sounds like that's what you're suggesting here as a possible solution.
I just finished talking to guy who is selling his 02r96v2 (which I've now
determined is way out of my price range - even used) and he shared an absolute
Tascam customer service horror story regarding a DM-24 he owned. 4 bad power
supplies, LCD failed, lost studio time (had to ship it back something like
6 times - from Hawaii!!!!) and Tascam apparently never did make it right
for him.
Hopefully they got it right with the new boards because the resounding impression
I'm getting of Tascam's willingness/ability to stand behind their products
is the only thing causing hesitation for me right now.
Cheers,
Jon
"LaMont " <jjdpro@ameritech.net> wrote:
>
>Hey Jon,
>
>Trust me, the marriage of the Tascam 3200 & Cuabse 4 is a match made in
heaven.
>You will not miss the Paris sound.
>
>However to not throw away your Paris investment(s), instead of summing out
>of the 3200..you can...
>
>Another way.. 3200 out via SP/Dif. into Paris Mec/442 SP/dif..for just a
>stereo sum .. Again, good sound.
>
>3200 master (analog outs) into Paris MEC/442.. 24bit(input Card)..then 24bit
>out card..to master or internal bounce..
>
>You can't loose either way you go.. Grat choice!!
>P.S. Put into an Argosy!!! :)
>take care.
>
>- 3200 out (Adat x 2) 16 lightpipes stems into MEC (with 2 adat cards)..
>For stem mixing. Very cool.. Very good sound. and provides a means of Matering
>within Paris.
>
>"Jon Jiles" <nojij@yahoo.com> wrote:
>>
>>Wow!!!!
>>
>>That's a pretty ringing endorsement LaMont!!!!
>>
>>I'm definitely leaning towards the 3200 and Cubase 4. The only client in
>>my studio is me and I'm really just trying to get to a simpler workflow
>,for
>>the songwriting end of things, and still achieve quality results at the
>end
>>of the process.
>>
>>Can you eplain to me in a little more detail how you (and apparently BT)
>>would be/are using Paris as the master summing mixer/recorder in this scenario?
>>
>>I've currently got Cubase SX3 lightpiped into Paris via a RME 9652 ( a
mini-Deej
>>set-up if, you will) but being a guy who only gets to work on my stuff
in
>>the evenings after work or on the weekends, the opportunity for confusion
>>in such a kludge ridden set-up doesn't lend itself to the creative workflow.
>>That's why Cubase and a nice board/control surface appeals. My big dilemma
>>though is that I still absolutely love the way Paris sounds.
>>
>>Anyway, thanks a ton for the input, greatly appreciated! I've got much
to
>>consider.
>>
>>Cheers,
>>jon
>>
>>
>>"LaMont" <jjdpro@ameritech.net> wrote:
>>>
>>>Hi Jon, I can chime in here on this question.
>>>
>>>I often work at a local studio http://www.lamourrecording.com/
>>>which has (2) Yamaha's DM2000. I can't speak highly enough of these powerful
>>>beast.
>>>
>>>Great feel, 96 channels @ 96K
>>>Pro Tools, Neundo/Cubase/Sonar/Logic Controller
>>>Nice Comps/EQs on every channel
>>>(8) SPX-1000's DSP processors (REVerbs, Delays, Chorus.etc)
>>>Some of the sweetest (24) Mic pres you'll find
>>>All in a foot print that keeps the Engineer/Operator right in
>>>front of the mix..There's a ton more features..
>>>
>>>I had a chance (2years) ago to take the then Tascam 3200 for week session
>>>spin. Due to the fact that no body in our area had a O2r/96, we rented
>>>the tascam.. Man, to my ears and others, the Tascam delivers the goods.
>>I
>>>would have to say that the Tascam 3200 sonics was more "thick" than the
>>DM2000.
>>>Different converters and clocks.. But, we mananged to get thru a sesion
>>without
>>>opening the manual!!
>>>You're not going to do that with the Yammys.. he 3200 had full eq and
dynamics
>>>on every channel as well as I think 4 DSP processors for Verbs and dleays
>>>chorus FX.. The verbs were the star of this board. The algo's were from
>>TC!!
>>>the verb masters. Man, these verbs sounded like our TC 3000 ..really!!.
>>The
>>>Eqs were usuable as are the Comps/Lim..We click on the DAW controller
layer
>>>button, scrolled to the DAW template (Pro Tools)..Boom!! "Houston We have
>>>Controll".. That easy.. We had transport, channel faders and Master faders
>>>and edit scroll.. To be honest, we probable had more functions,but like
>>I
>>>stated earlier, we had not read the manual..
>>>Oh well.
>>>
>>>Like I told James, I'm looking seriously @ the DM4800 X2 for my Home studio..To
>>>host Both Nuendo & Pro Tools...AND yes, Liek BrianT does in Houston, Paris
>>>will be used a he master summing mixer/recorder..
>>>
>>>The DM3200/4800 can't be beat in their price range. They have the sound,
>>>looks, and product maturity. Tascam knew they had a winner with the DM24,then
>>>knocked the ball out of the park with the DM3200, and now DM 4800..
>>>
>>>Now that it's official that Mackie has dropped the Ball with the DXB(20K
>>>Plus), now selling are drastic discounts. The DXB is a one sweet sounding
>>>board as well. At 9k it competes very well with Yammys O2r/96..But, (2)
>>x
>>>DM4800 @ around is just as and (imo) more potent ..AND dropped in a cool
>>>Argosy, BAMM!..
>>>
>>>http://www.argosyconsole.com/dm3200.htm
>>>
>>>
>>>
>>>"Jon Jiles" <nanaheyhey@no.com> wrote:
>>>>
>>>>Thanks for all the info James!
>>>>
>>>>How do they stack up against the Yamaha boards? (O2r96v2 and the DM1000v2,etc)
>>>>Also, Cubase implementation will be a key factor if I move from Paris.
>>I
>>>>will consider the Yamaha boards too (used though due to price) because
>>of
>>>>the Yammy/Steinberg connection and better Cubase implementation I would
>>>suppose.
>>>>The Tascam boards do seem like a very good value though... especially
>if
>>>>they don't break and are not horribly non-intuitive.
>>>>
>>>>Thanks again,
>>>>Jon
>>>>
>>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>>
>>>>>By the way, the mic pres on the DM-32 and DM-48 are greatly improved
>and
>>>>vary
>>>>>usable. It was only the DM-24 that had the problems.
>>>>>
>>>>>James
>>>>>
>>>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>>>
>>>>>>Hey Jon!
>>>>>>
>>>>>>Some of the guys on the DA7 NG have switched to the Tascam DM 32s.
>A
>>>customer
>>>>>>of mine also has one. The mixes from both source sound good. You
should
>>>>>>always test drive before you buy. You have to like it. I would think
>>>>twice
>>>>>>before buying a DM-24, the Mic pres were not so good, they had low
head
>>>>>room.
>>>>>> If you use the DM-24 for line ins only, I think you'd be Ok. There
>>was
>>>>>>an upgrade for the mic pres through Tascam, they may no longer be doing
>>>>>that.
>>>>>>
>>>>>>I hear the DM manuals are terrible, you can go down load them. If
you
>>>>buy
>>>>>>one, make sure you have 30 full days to test it. Clear your planner
>>for
>>>>>>test time. Read the manual in advance and go to the NG a lot before
>>you
>>>>>>get it. Every once in awhile Tascam puts out a lemon, so you want
to
>>>be
>>>>>>able to fully test what you buy from them. Unless they have changed
>>their
>>>>>>policy, they only have a 90 day warranty!!!
>>>>>>
>>>>>>James
>>>>>>
>>>>>>"Jon Jiles" <snoid@sheboygan.com> wrote:
>>>>>>>
>>>>>>>Hi,
>>>>>>>
>>>>>>>Anyone here actually had any real hands on with this board/controller,
>>>>>especially
>>>>>>>with Cubase 4? James got me intrigued but I have read that the build
>>>quolity
>>>>>>>may be somewhat on cheesy side.
>>>>>>>
>>>>>>>Thanks,
>>>>>>>Jon
>>>>>>
>>>>>
>>>>
>>>
>>
>
|
|
|
|
| Re: Any Tascam 3200/4800 users here?...YES!!! [message #79187 is a reply to message #79180] |
Mon, 29 January 2007 13:41 |
Jon Jiles
Messages: 90
Registered: November 2005
|
Member |
|
|
Hey James!
Just had a chance to check out the Mike Ofca links.
I have to say that while the tune isn't really my favorite genre,
I thought both mixes sounded pretty damn good!!
Especially liked the Satriani inspired movie thing in the studio.
Again , I can't thank all of you guys who have chimed in enough for all of
your input.
Thanks,
Jon
"James McCloskey" <excelsm@hotmail.com> wrote:
>
>It should be noted that the 442 SP/DIF is only 20bit. The SP/DIF on the
MEC
>is 24bit.
>
>James
>
>"LaMont " <jjdpro@ameritech.net> wrote:
>>
>>Hey Jon,
>>
>>Trust me, the marriage of the Tascam 3200 & Cuabse 4 is a match made in
>heaven.
>>You will not miss the Paris sound.
>>
>>However to not throw away your Paris investment(s), instead of summing
out
>>of the 3200..you can...
>>
>>Another way.. 3200 out via SP/Dif. into Paris Mec/442 SP/dif..for just
a
>>stereo sum .. Again, good sound.
>>
>>3200 master (analog outs) into Paris MEC/442.. 24bit(input Card)..then
24bit
>>out card..to master or internal bounce..
>>
>>You can't loose either way you go.. Grat choice!!
>>P.S. Put into an Argosy!!! :)
>>take care.
>>
>>- 3200 out (Adat x 2) 16 lightpipes stems into MEC (with 2 adat cards)..
>>For stem mixing. Very cool.. Very good sound. and provides a means of Matering
>>within Paris.
>>
>>"Jon Jiles" <nojij@yahoo.com> wrote:
>>>
>>>Wow!!!!
>>>
>>>That's a pretty ringing endorsement LaMont!!!!
>>>
>>>I'm definitely leaning towards the 3200 and Cubase 4. The only client
in
>>>my studio is me and I'm really just trying to get to a simpler workflow
>>,for
>>>the songwriting end of things, and still achieve quality results at the
>>end
>>>of the process.
>>>
>>>Can you eplain to me in a little more detail how you (and apparently BT)
>>>would be/are using Paris as the master summing mixer/recorder in this
scenario?
>>>
>>>I've currently got Cubase SX3 lightpiped into Paris via a RME 9652 ( a
>mini-Deej
>>>set-up if, you will) but being a guy who only gets to work on my stuff
>in
>>>the evenings after work or on the weekends, the opportunity for confusion
>>>in such a kludge ridden set-up doesn't lend itself to the creative workflow.
>>>That's why Cubase and a nice board/control surface appeals. My big dilemma
>>>though is that I still absolutely love the way Paris sounds.
>>>
>>>Anyway, thanks a ton for the input, greatly appreciated! I've got much
>to
>>>consider.
>>>
>>>Cheers,
>>>jon
>>>
>>>
>>>"LaMont" <jjdpro@ameritech.net> wrote:
>>>>
>>>>Hi Jon, I can chime in here on this question.
>>>>
>>>>I often work at a local studio http://www.lamourrecording.com/
>>>>which has (2) Yamaha's DM2000. I can't speak highly enough of these powerful
>>>>beast.
>>>>
>>>>Great feel, 96 channels @ 96K
>>>>Pro Tools, Neundo/Cubase/Sonar/Logic Controller
>>>>Nice Comps/EQs on every channel
>>>>(8) SPX-1000's DSP processors (REVerbs, Delays, Chorus.etc)
>>>>Some of the sweetest (24) Mic pres you'll find
>>>>All in a foot print that keeps the Engineer/Operator right in
>>>>front of the mix..There's a ton more features..
>>>>
>>>>I had a chance (2years) ago to take the then Tascam 3200 for week session
>>>>spin. Due to the fact that no body in our area had a O2r/96, we rented
>>>>the tascam.. Man, to my ears and others, the Tascam delivers the goods.
>>>I
>>>>would have to say that the Tascam 3200 sonics was more "thick" than the
>>>DM2000.
>>>>Different converters and clocks.. But, we mananged to get thru a sesion
>>>without
>>>>opening the manual!!
>>>>You're not going to do that with the Yammys.. he 3200 had full eq and
>dynamics
>>>>on every channel as well as I think 4 DSP processors for Verbs and dleays
>>>>chorus FX.. The verbs were the star of this board. The algo's were from
>>>TC!!
>>>>the verb masters. Man, these verbs sounded like our TC 3000 ..really!!.
>>>The
>>>>Eqs were usuable as are the Comps/Lim..We click on the DAW controller
>layer
>>>>button, scrolled to the DAW template (Pro Tools)..Boom!! "Houston We
have
>>>>Controll".. That easy.. We had transport, channel faders and Master faders
>>>>and edit scroll.. To be honest, we probable had more functions,but like
>>>I
>>>>stated earlier, we had not read the manual..
>>>>Oh well.
>>>>
>>>>Like I told James, I'm looking seriously @ the DM4800 X2 for my Home
studio..To
>>>>host Both Nuendo & Pro Tools...AND yes, Liek BrianT does in Houston,
Paris
>>>>will be used a he master summing mixer/recorder..
>>>>
>>>>The DM3200/4800 can't be beat in their price range. They have the sound,
>>>>looks, and product maturity. Tascam knew they had a winner with the DM24,then
>>>>knocked the ball out of the park with the DM3200, and now DM 4800..
>>>>
>>>>Now that it's official that Mackie has dropped the Ball with the DXB(20K
>>>>Plus), now selling are drastic discounts. The DXB is a one sweet sounding
>>>>board as well. At 9k it competes very well with Yammys O2r/96..But, (2)
>>>x
>>>>DM4800 @ around is just as and (imo) more potent ..AND dropped in a cool
>>>>Argosy, BAMM!..
>>>>
>>>>http://www.argosyconsole.com/dm3200.htm
>>>>
>>>>
>>>>
>>>>"Jon Jiles" <nanaheyhey@no.com> wrote:
>>>>>
>>>>>Thanks for all the info James!
>>>>>
>>>>>How do they stack up against the Yamaha boards? (O2r96v2 and the DM1000v2,etc)
>>>>>Also, Cubase implementation will be a key factor if I move from Paris.
>>>I
>>>>>will consider the Yamaha boards too (used though due to price) because
>>>of
>>>>>the Yammy/Steinberg connection and better Cubase implementation I would
>>>>suppose.
>>>>>The Tascam boards do seem like a very good value though... especially
>>if
>>>>>they don't break and are not horribly non-intuitive.
>>>>>
>>>>>Thanks again,
>>>>>Jon
>>>>>
>>>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>>>
>>>>>>By the way, the mic pres on the DM-32 and DM-48 are greatly improved
>>and
>>>>>vary
>>>>>>usable. It was only the DM-24 that had the problems.
>>>>>>
>>>>>>James
>>>>>>
>>>>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>>>>
>>>>>>>Hey Jon!
>>>>>>>
>>>>>>>Some of the guys on the DA7 NG have switched to the Tascam DM 32s.
>
>>A
>>>>customer
>>>>>>>of mine also has one. The mixes from both source sound good. You
>should
>>>>>>>always test drive before you buy. You have to like it. I would think
>>>>>twice
>>>>>>>before buying a DM-24, the Mic pres were not so good, they had low
>head
>>>>>>room.
>>>>>>> If you use the DM-24 for line ins only, I think you'd be Ok. There
>>>was
>>>>>>>an upgrade for the mic pres through Tascam, they may no longer be
doing
>>>>>>that.
>>>>>>>
>>>>>>>I hear the DM manuals are terrible, you can go down load them. If
>you
>>>>>buy
>>>>>>>one, make sure you have 30 full days to test it. Clear your planner
>>>for
>>>>>>>test time. Read the manual in advance and go to the NG a lot before
>>>you
>>>>>>>get it. Every once in awhile Tascam puts out a lemon, so you want
>to
>>>>be
>>>>>>>able to fully test what you buy from them. Unless they have changed
>>>their
>>>>>>>policy, they only have a 90 day warranty!!!
>>>>>>>
>>>>>>>James
>>>>>>>
>>>>>>>"Jon Jiles" <snoid@sheboygan.com> wrote:
>>>>>>>>
>>>>>>>>Hi,
>>>>>>>>
>>>>>>>>Anyone here actually had any real hands on with this board/controller,
>>>>>>especially
>>>>>>>>with Cubase 4? James got me intrigued but I have read that the build
>>>>quolity
>>>>>>>>may be somewhat on cheesy side.
>>>>>>>>
>>>>>>>>Thanks,
>>>>>>>>Jon
>>>>>>>
>>>>>>
>>>>>
>>>>
>>>
>>
>
|
|
|
|
| Re: Any Tascam 3200/4800 users here?...YES!!! [message #79192 is a reply to message #79180] |
Mon, 29 January 2007 13:55 |
LaMont
Messages: 828
Registered: October 2005
|
Senior Member |
|
|
You're right.. But, The best 20bit conveterts I've heard and can hang with
the best 24bit and even most so-called 96k converters..
:)
"James McCloskey" <excelsm@hotmail.com> wrote:
>
>It should be noted that the 442 SP/DIF is only 20bit. The SP/DIF on the
MEC
>is 24bit.
>
>James
>
>"LaMont " <jjdpro@ameritech.net> wrote:
>>
>>Hey Jon,
>>
>>Trust me, the marriage of the Tascam 3200 & Cuabse 4 is a match made in
>heaven.
>>You will not miss the Paris sound.
>>
>>However to not throw away your Paris investment(s), instead of summing
out
>>of the 3200..you can...
>>
>>Another way.. 3200 out via SP/Dif. into Paris Mec/442 SP/dif..for just
a
>>stereo sum .. Again, good sound.
>>
>>3200 master (analog outs) into Paris MEC/442.. 24bit(input Card)..then
24bit
>>out card..to master or internal bounce..
>>
>>You can't loose either way you go.. Grat choice!!
>>P.S. Put into an Argosy!!! :)
>>take care.
>>
>>- 3200 out (Adat x 2) 16 lightpipes stems into MEC (with 2 adat cards)..
>>For stem mixing. Very cool.. Very good sound. and provides a means of Matering
>>within Paris.
>>
>>"Jon Jiles" <nojij@yahoo.com> wrote:
>>>
>>>Wow!!!!
>>>
>>>That's a pretty ringing endorsement LaMont!!!!
>>>
>>>I'm definitely leaning towards the 3200 and Cubase 4. The only client
in
>>>my studio is me and I'm really just trying to get to a simpler workflow
>>,for
>>>the songwriting end of things, and still achieve quality results at the
>>end
>>>of the process.
>>>
>>>Can you eplain to me in a little more detail how you (and apparently BT)
>>>would be/are using Paris as the master summing mixer/recorder in this
scenario?
>>>
>>>I've currently got Cubase SX3 lightpiped into Paris via a RME 9652 ( a
>mini-Deej
>>>set-up if, you will) but being a guy who only gets to work on my stuff
>in
>>>the evenings after work or on the weekends, the opportunity for confusion
>>>in such a kludge ridden set-up doesn't lend itself to the creative workflow.
>>>That's why Cubase and a nice board/control surface appeals. My big dilemma
>>>though is that I still absolutely love the way Paris sounds.
>>>
>>>Anyway, thanks a ton for the input, greatly appreciated! I've got much
>to
>>>consider.
>>>
>>>Cheers,
>>>jon
>>>
>>>
>>>"LaMont" <jjdpro@ameritech.net> wrote:
>>>>
>>>>Hi Jon, I can chime in here on this question.
>>>>
>>>>I often work at a local studio http://www.lamourrecording.com/
>>>>which has (2) Yamaha's DM2000. I can't speak highly enough of these powerful
>>>>beast.
>>>>
>>>>Great feel, 96 channels @ 96K
>>>>Pro Tools, Neundo/Cubase/Sonar/Logic Controller
>>>>Nice Comps/EQs on every channel
>>>>(8) SPX-1000's DSP processors (REVerbs, Delays, Chorus.etc)
>>>>Some of the sweetest (24) Mic pres you'll find
>>>>All in a foot print that keeps the Engineer/Operator right in
>>>>front of the mix..There's a ton more features..
>>>>
>>>>I had a chance (2years) ago to take the then Tascam 3200 for week session
>>>>spin. Due to the fact that no body in our area had a O2r/96, we rented
>>>>the tascam.. Man, to my ears and others, the Tascam delivers the goods.
>>>I
>>>>would have to say that the Tascam 3200 sonics was more "thick" than the
>>>DM2000.
>>>>Different converters and clocks.. But, we mananged to get thru a sesion
>>>without
>>>>opening the manual!!
>>>>You're not going to do that with the Yammys.. he 3200 had full eq and
>dynamics
>>>>on every channel as well as I think 4 DSP processors for Verbs and dleays
>>>>chorus FX.. The verbs were the star of this board. The algo's were from
>>>TC!!
>>>>the verb masters. Man, these verbs sounded like our TC 3000 ..really!!.
>>>The
>>>>Eqs were usuable as are the Comps/Lim..We click on the DAW controller
>layer
>>>>button, scrolled to the DAW template (Pro Tools)..Boom!! "Houston We
have
>>>>Controll".. That easy.. We had transport, channel faders and Master faders
>>>>and edit scroll.. To be honest, we probable had more functions,but like
>>>I
>>>>stated earlier, we had not read the manual..
>>>>Oh well.
>>>>
>>>>Like I told James, I'm looking seriously @ the DM4800 X2 for my Home
studio..To
>>>>host Both Nuendo & Pro Tools...AND yes, Liek BrianT does in Houston,
Paris
>>>>will be used a he master summing mixer/recorder..
>>>>
>>>>The DM3200/4800 can't be beat in their price range. They have the sound,
>>>>looks, and product maturity. Tascam knew they had a winner with the DM24,then
>>>>knocked the ball out of the park with the DM3200, and now DM 4800..
>>>>
>>>>Now that it's official that Mackie has dropped the Ball with the DXB(20K
>>>>Plus), now selling are drastic discounts. The DXB is a one sweet sounding
>>>>board as well. At 9k it competes very well with Yammys O2r/96..But, (2)
>>>x
>>>>DM4800 @ around is just as and (imo) more potent ..AND dropped in a cool
>>>>Argosy, BAMM!..
>>>>
>>>>http://www.argosyconsole.com/dm3200.htm
>>>>
>>>>
>>>>
>>>>"Jon Jiles" <nanaheyhey@no.com> wrote:
>>>>>
>>>>>Thanks for all the info James!
>>>>>
>>>>>How do they stack up against the Yamaha boards? (O2r96v2 and the DM1000v2,etc)
>>>>>Also, Cubase implementation will be a key factor if I move from Paris.
>>>I
>>>>>will consider the Yamaha boards too (used though due to price) because
>>>of
>>>>>the Yammy/Steinberg connection and better Cubase implementation I would
>>>>suppose.
>>>>>The Tascam boards do seem like a very good value though... especially
>>if
>>>>>they don't break and are not horribly non-intuitive.
>>>>>
>>>>>Thanks again,
>>>>>Jon
>>>>>
>>>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>>>
>>>>>>By the way, the mic pres on the DM-32 and DM-48 are greatly improved
>>and
>>>>>vary
>>>>>>usable. It was only the DM-24 that had the problems.
>>>>>>
>>>>>>James
>>>>>>
>>>>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>>>>
>>>>>>>Hey Jon!
>>>>>>>
>>>>>>>Some of the guys on the DA7 NG have switched to the Tascam DM 32s.
>
>>A
>>>>customer
>>>>>>>of mine also has one. The mixes from both source sound good. You
>should
>>>>>>>always test drive before you buy. You have to like it. I would think
>>>>>twice
>>>>>>>before buying a DM-24, the Mic pres were not so good, they had low
>head
>>>>>>room.
>>>>>>> If you use the DM-24 for line ins only, I think you'd be Ok. There
>>>was
>>>>>>>an upgrade for the mic pres through Tascam, they may no longer be
doing
>>>>>>that.
>>>>>>>
>>>>>>>I hear the DM manuals are terrible, you can go down load them. If
>you
>>>>>buy
>>>>>>>one, make sure you have 30 full days to test it. Clear your planner
>>>for
>>>>>>>test time. Read the manual in advance and go to the NG a lot before
>>>you
>>>>>>>get it. Every once in awhile Tascam puts out a lemon, so you want
>to
>>>>be
>>>>>>>able to fully test what you buy from them. Unless they have changed
>>>their
>>>>>>>policy, they only have a 90 day warranty!!!
>>>>>>>
>>>>>>>James
>>>>>>>
>>>>>>>"Jon Jiles" <snoid@sheboygan.com> wrote:
>>>>>>>>
>>>>>>>>Hi,
>>>>>>>>
>>>>>>>>Anyone here actually had any real hands on with this board/controller,
>>>>>>especially
>>>>>>>>with Cubase 4? James got me intrigued but I have read that the build
>>>>quolity
>>>>>>>>may be somewhat on cheesy side.
>>>>>>>>
>>>>>>>>Thanks,
>>>>>>>>Jon
>>>>>>>
>>>>>>
>>>>>
>>>>
>>>
>>
>
|
|
|
|
| Re: Any Tascam 3200/4800 users here?...YES!!! [message #79193 is a reply to message #79184] |
Mon, 29 January 2007 13:58 |
LaMont
Messages: 828
Registered: October 2005
|
Senior Member |
|
|
Hey Jon,
- most DM24 users/owners units have been rock solid
- having stated the above, Yamaha Desks are as solid as they come. They rarley
break down. O2rs(orignals) are still cranking to this day.
Have you considerd the Firewire Option? 32/32 ins/outs?
"Jon Jiles" <nojij@yahoo.com> wrote:
>
>Thanks LaMont -
>
>I had considered keeping some of my Paris rig to use as a glorified mastering
>deck. Sounds like that's what you're suggesting here as a possible solution.
>
>I just finished talking to guy who is selling his 02r96v2 (which I've now
>determined is way out of my price range - even used) and he shared an absolute
>Tascam customer service horror story regarding a DM-24 he owned. 4 bad power
>supplies, LCD failed, lost studio time (had to ship it back something like
>6 times - from Hawaii!!!!) and Tascam apparently never did make it right
>for him.
>
>Hopefully they got it right with the new boards because the resounding impression
>I'm getting of Tascam's willingness/ability to stand behind their products
>is the only thing causing hesitation for me right now.
>
>Cheers,
>Jon
>
>"LaMont " <jjdpro@ameritech.net> wrote:
>>
>>Hey Jon,
>>
>>Trust me, the marriage of the Tascam 3200 & Cuabse 4 is a match made in
>heaven.
>>You will not miss the Paris sound.
>>
>>However to not throw away your Paris investment(s), instead of summing
out
>>of the 3200..you can...
>>
>>Another way.. 3200 out via SP/Dif. into Paris Mec/442 SP/dif..for just
a
>>stereo sum .. Again, good sound.
>>
>>3200 master (analog outs) into Paris MEC/442.. 24bit(input Card)..then
24bit
>>out card..to master or internal bounce..
>>
>>You can't loose either way you go.. Grat choice!!
>>P.S. Put into an Argosy!!! :)
>>take care.
>>
>>- 3200 out (Adat x 2) 16 lightpipes stems into MEC (with 2 adat cards)..
>>For stem mixing. Very cool.. Very good sound. and provides a means of Matering
>>within Paris.
>>
>>"Jon Jiles" <nojij@yahoo.com> wrote:
>>>
>>>Wow!!!!
>>>
>>>That's a pretty ringing endorsement LaMont!!!!
>>>
>>>I'm definitely leaning towards the 3200 and Cubase 4. The only client
in
>>>my studio is me and I'm really just trying to get to a simpler workflow
>>,for
>>>the songwriting end of things, and still achieve quality results at the
>>end
>>>of the process.
>>>
>>>Can you eplain to me in a little more detail how you (and apparently BT)
>>>would be/are using Paris as the master summing mixer/recorder in this
scenario?
>>>
>>>I've currently got Cubase SX3 lightpiped into Paris via a RME 9652 ( a
>mini-Deej
>>>set-up if, you will) but being a guy who only gets to work on my stuff
>in
>>>the evenings after work or on the weekends, the opportunity for confusion
>>>in such a kludge ridden set-up doesn't lend itself to the creative workflow.
>>>That's why Cubase and a nice board/control surface appeals. My big dilemma
>>>though is that I still absolutely love the way Paris sounds.
>>>
>>>Anyway, thanks a ton for the input, greatly appreciated! I've got much
>to
>>>consider.
>>>
>>>Cheers,
>>>jon
>>>
>>>
>>>"LaMont" <jjdpro@ameritech.net> wrote:
>>>>
>>>>Hi Jon, I can chime in here on this question.
>>>>
>>>>I often work at a local studio http://www.lamourrecording.com/
>>>>which has (2) Yamaha's DM2000. I can't speak highly enough of these powerful
>>>>beast.
>>>>
>>>>Great feel, 96 channels @ 96K
>>>>Pro Tools, Neundo/Cubase/Sonar/Logic Controller
>>>>Nice Comps/EQs on every channel
>>>>(8) SPX-1000's DSP processors (REVerbs, Delays, Chorus.etc)
>>>>Some of the sweetest (24) Mic pres you'll find
>>>>All in a foot print that keeps the Engineer/Operator right in
>>>>front of the mix..There's a ton more features..
>>>>
>>>>I had a chance (2years) ago to take the then Tascam 3200 for week session
>>>>spin. Due to the fact that no body in our area had a O2r/96, we rented
>>>>the tascam.. Man, to my ears and others, the Tascam delivers the goods.
>>>I
>>>>would have to say that the Tascam 3200 sonics was more "thick" than the
>>>DM2000.
>>>>Different converters and clocks.. But, we mananged to get thru a sesion
>>>without
>>>>opening the manual!!
>>>>You're not going to do that with the Yammys.. he 3200 had full eq and
>dynamics
>>>>on every channel as well as I think 4 DSP processors for Verbs and dleays
>>>>chorus FX.. The verbs were the star of this board. The algo's were from
>>>TC!!
>>>>the verb masters. Man, these verbs sounded like our TC 3000 ..really!!.
>>>The
>>>>Eqs were usuable as are the Comps/Lim..We click on the DAW controller
>layer
>>>>button, scrolled to the DAW template (Pro Tools)..Boom!! "Houston We
have
>>>>Controll".. That easy.. We had transport, channel faders and Master faders
>>>>and edit scroll.. To be honest, we probable had more functions,but like
>>>I
>>>>stated earlier, we had not read the manual..
>>>>Oh well.
>>>>
>>>>Like I told James, I'm looking seriously @ the DM4800 X2 for my Home
studio..To
>>>>host Both Nuendo & Pro Tools...AND yes, Liek BrianT does in Houston,
Paris
>>>>will be used a he master summing mixer/recorder..
>>>>
>>>>The DM3200/4800 can't be beat in their price range. They have the sound,
>>>>looks, and product maturity. Tascam knew they had a winner with the DM24,then
>>>>knocked the ball out of the park with the DM3200, and now DM 4800..
>>>>
>>>>Now that it's official that Mackie has dropped the Ball with the DXB(20K
>>>>Plus), now selling are drastic discounts. The DXB is a one sweet sounding
>>>>board as well. At 9k it competes very well with Yammys O2r/96..But, (2)
>>>x
>>>>DM4800 @ around is just as and (imo) more potent ..AND dropped in a cool
>>>>Argosy, BAMM!..
>>>>
>>>>http://www.argosyconsole.com/dm3200.htm
>>>>
>>>>
>>>>
>>>>"Jon Jiles" <nanaheyhey@no.com> wrote:
>>>>>
>>>>>Thanks for all the info James!
>>>>>
>>>>>How do they stack up against the Yamaha boards? (O2r96v2 and the DM1000v2,etc)
>>>>>Also, Cubase implementation will be a key factor if I move from Paris.
>>>I
>>>>>will consider the Yamaha boards too (used though due to price) because
>>>of
>>>>>the Yammy/Steinberg connection and better Cubase implementation I would
>>>>suppose.
>>>>>The Tascam boards do seem like a very good value though... especially
>>if
>>>>>they don't break and are not horribly non-intuitive.
>>>>>
>>>>>Thanks again,
>>>>>Jon
>>>>>
>>>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>>>
>>>>>>By the way, the mic pres on the DM-32 and DM-48 are greatly improved
>>and
>>>>>vary
>>>>>>usable. It was only the DM-24 that had the problems.
>>>>>>
>>>>>>James
>>>>>>
>>>>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>>>>
>>>>>>>Hey Jon!
>>>>>>>
>>>>>>>Some of the guys on the DA7 NG have switched to the Tascam DM 32s.
>
>>A
>>>>customer
>>>>>>>of mine also has one. The mixes from both source sound good. You
>should
>>>>>>>always test drive before you buy. You have to like it. I would think
>>>>>twice
>>>>>>>before buying a DM-24, the Mic pres were not so good, they had low
>head
>>>>>>room.
>>>>>>> If you use the DM-24 for line ins only, I think you'd be Ok. There
>>>was
>>>>>>>an upgrade for the mic pres through Tascam, they may no longer be
doing
>>>>>>that.
>>>>>>>
>>>>>>>I hear the DM manuals are terrible, you can go down load them. If
>you
>>>>>buy
>>>>>>>one, make sure you have 30 full days to test it. Clear your planner
>>>for
>>>>>>>test time. Read the manual in advance and go to the NG a lot before
>>>you
>>>>>>>get it. Every once in awhile Tascam puts out a lemon, so you want
>to
>>>>be
>>>>>>>able to fully test what you buy from them. Unless they have changed
>>>their
>>>>>>>policy, they only have a 90 day warranty!!!
>>>>>>>
>>>>>>>James
>>>>>>>
>>>>>>>"Jon Jiles" <snoid@sheboygan.com> wrote:
>>>>>>>>
>>>>>>>>Hi,
>>>>>>>>
>>>>>>>>Anyone here actually had any real hands on with this board/controller,
>>>>>>especially
>>>>>>>>with Cubase 4? James got me intrigued but I have read that the build
>>>>quolity
>>>>>>>>may be somewhat on cheesy side.
>>>>>>>>
>>>>>>>>Thanks,
>>>>>>>>Jon
>>>>>>>
>>>>>>
>>>>>
>>>>
>>>
>>
>
|
|
|
|
| Re: Any Tascam 3200/4800 users here?...YES!!! [message #79194 is a reply to message #79184] |
Mon, 29 January 2007 14:12 |
excelav
Messages: 2130
Registered: July 2005
Location: Metro Detroit
|
Senior Member |
|
|
Jon, I've heard the horror stories too. With any manufacture it's the luck
of the draw. Tascam only has a 90 day warranty. Like I said, clear your
slate and try one out for 30 days first. You could try to get the reseller
to agree to a return for a longer period of time if the product turns out
to be defective. Don't let the dealer try to talk you in to something else.
Remember, you could also get a good one too! For the money, I think it's
the way to go.
Good luck with your choice, and let us know what you end up doing.
James
"Jon Jiles" <nojij@yahoo.com> wrote:
>
>Thanks LaMont -
>
>I had considered keeping some of my Paris rig to use as a glorified mastering
>deck. Sounds like that's what you're suggesting here as a possible solution.
>
>I just finished talking to guy who is selling his 02r96v2 (which I've now
>determined is way out of my price range - even used) and he shared an absolute
>Tascam customer service horror story regarding a DM-24 he owned. 4 bad power
>supplies, LCD failed, lost studio time (had to ship it back something like
>6 times - from Hawaii!!!!) and Tascam apparently never did make it right
>for him.
>
>Hopefully they got it right with the new boards because the resounding impression
>I'm getting of Tascam's willingness/ability to stand behind their products
>is the only thing causing hesitation for me right now.
>
>Cheers,
>Jon
>
>"LaMont " <jjdpro@ameritech.net> wrote:
>>
>>Hey Jon,
>>
>>Trust me, the marriage of the Tascam 3200 & Cuabse 4 is a match made in
>heaven.
>>You will not miss the Paris sound.
>>
>>However to not throw away your Paris investment(s), instead of summing
out
>>of the 3200..you can...
>>
>>Another way.. 3200 out via SP/Dif. into Paris Mec/442 SP/dif..for just
a
>>stereo sum .. Again, good sound.
>>
>>3200 master (analog outs) into Paris MEC/442.. 24bit(input Card)..then
24bit
>>out card..to master or internal bounce..
>>
>>You can't loose either way you go.. Grat choice!!
>>P.S. Put into an Argosy!!! :)
>>take care.
>>
>>- 3200 out (Adat x 2) 16 lightpipes stems into MEC (with 2 adat cards)..
>>For stem mixing. Very cool.. Very good sound. and provides a means of Matering
>>within Paris.
>>
>>"Jon Jiles" <nojij@yahoo.com> wrote:
>>>
>>>Wow!!!!
>>>
>>>That's a pretty ringing endorsement LaMont!!!!
>>>
>>>I'm definitely leaning towards the 3200 and Cubase 4. The only client
in
>>>my studio is me and I'm really just trying to get to a simpler workflow
>>,for
>>>the songwriting end of things, and still achieve quality results at the
>>end
>>>of the process.
>>>
>>>Can you eplain to me in a little more detail how you (and apparently BT)
>>>would be/are using Paris as the master summing mixer/recorder in this
scenario?
>>>
>>>I've currently got Cubase SX3 lightpiped into Paris via a RME 9652 ( a
>mini-Deej
>>>set-up if, you will) but being a guy who only gets to work on my stuff
>in
>>>the evenings after work or on the weekends, the opportunity for confusion
>>>in such a kludge ridden set-up doesn't lend itself to the creative workflow.
>>>That's why Cubase and a nice board/control surface appeals. My big dilemma
>>>though is that I still absolutely love the way Paris sounds.
>>>
>>>Anyway, thanks a ton for the input, greatly appreciated! I've got much
>to
>>>consider.
>>>
>>>Cheers,
>>>jon
>>>
>>>
>>>"LaMont" <jjdpro@ameritech.net> wrote:
>>>>
>>>>Hi Jon, I can chime in here on this question.
>>>>
>>>>I often work at a local studio http://www.lamourrecording.com/
>>>>which has (2) Yamaha's DM2000. I can't speak highly enough of these powerful
>>>>beast.
>>>>
>>>>Great feel, 96 channels @ 96K
>>>>Pro Tools, Neundo/Cubase/Sonar/Logic Controller
>>>>Nice Comps/EQs on every channel
>>>>(8) SPX-1000's DSP processors (REVerbs, Delays, Chorus.etc)
>>>>Some of the sweetest (24) Mic pres you'll find
>>>>All in a foot print that keeps the Engineer/Operator right in
>>>>front of the mix..There's a ton more features..
>>>>
>>>>I had a chance (2years) ago to take the then Tascam 3200 for week session
>>>>spin. Due to the fact that no body in our area had a O2r/96, we rented
>>>>the tascam.. Man, to my ears and others, the Tascam delivers the goods.
>>>I
>>>>would have to say that the Tascam 3200 sonics was more "thick" than the
>>>DM2000.
>>>>Different converters and clocks.. But, we mananged to get thru a sesion
>>>without
>>>>opening the manual!!
>>>>You're not going to do that with the Yammys.. he 3200 had full eq and
>dynamics
>>>>on every channel as well as I think 4 DSP processors for Verbs and dleays
>>>>chorus FX.. The verbs were the star of this board. The algo's were from
>>>TC!!
>>>>the verb masters. Man, these verbs sounded like our TC 3000 ..really!!.
>>>The
>>>>Eqs were usuable as are the Comps/Lim..We click on the DAW controller
>layer
>>>>button, scrolled to the DAW template (Pro Tools)..Boom!! "Houston We
have
>>>>Controll".. That easy.. We had transport, channel faders and Master faders
>>>>and edit scroll.. To be honest, we probable had more functions,but like
>>>I
>>>>stated earlier, we had not read the manual..
>>>>Oh well.
>>>>
>>>>Like I told James, I'm looking seriously @ the DM4800 X2 for my Home
studio..To
>>>>host Both Nuendo & Pro Tools...AND yes, Liek BrianT does in Houston,
Paris
>>>>will be used a he master summing mixer/recorder..
>>>>
>>>>The DM3200/4800 can't be beat in their price range. They have the sound,
>>>>looks, and product maturity. Tascam knew they had a winner with the DM24,then
>>>>knocked the ball out of the park with the DM3200, and now DM 4800..
>>>>
>>>>Now that it's official that Mackie has dropped the Ball with the DXB(20K
>>>>Plus), now selling are drastic discounts. The DXB is a one sweet sounding
>>>>board as well. At 9k it competes very well with Yammys O2r/96..But, (2)
>>>x
>>>>DM4800 @ around is just as and (imo) more potent ..AND dropped in a cool
>>>>Argosy, BAMM!..
>>>>
>>>>http://www.argosyconsole.com/dm3200.htm
>>>>
>>>>
>>>>
>>>>"Jon Jiles" <nanaheyhey@no.com> wrote:
>>>>>
>>>>>Thanks for all the info James!
>>>>>
>>>>>How do they stack up against the Yamaha boards? (O2r96v2 and the DM1000v2,etc)
>>>>>Also, Cubase implementation will be a key factor if I move from Paris.
>>>I
>>>>>will consider the Yamaha boards too (used though due to price) because
>>>of
>>>>>the Yammy/Steinberg connection and better Cubase implementation I would
>>>>suppose.
>>>>>The Tascam boards do seem like a very good value though... especially
>>if
>>>>>they don't break and are not horribly non-intuitive.
>>>>>
>>>>>Thanks again,
>>>>>Jon
>>>>>
>>>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>>>
>>>>>>By the way, the mic pres on the DM-32 and DM-48 are greatly improved
>>and
>>>>>vary
>>>>>>usable. It was only the DM-24 that had the problems.
>>>>>>
>>>>>>James
>>>>>>
>>>>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>>>>
>>>>>>>Hey Jon!
>>>>>>>
>>>>>>>Some of the guys on the DA7 NG have switched to the Tascam DM 32s.
>
>>A
>>>>customer
>>>>>>>of mine also has one. The mixes from both source sound good. You
>should
>>>>>>>always test drive before you buy. You have to like it. I would think
>>>>>twice
>>>>>>>before buying a DM-24, the Mic pres were not so good, they had low
>head
>>>>>>room.
>>>>>>> If you use the DM-24 for line ins only, I think you'd be Ok. There
>>>was
>>>>>>>an upgrade for the mic pres through Tascam, they may no longer be
doing
>>>>>>that.
>>>>>>>
>>>>>>>I hear the DM manuals are terrible, you can go down load them. If
>you
>>>>>buy
>>>>>>>one, make sure you have 30 full days to test it. Clear your planner
>>>for
>>>>>>>test time. Read the manual in advance and go to the NG a lot before
>>>you
>>>>>>>get it. Every once in awhile Tascam puts out a lemon, so you want
>to
>>>>be
>>>>>>>able to fully test what you buy from them. Unless they have changed
>>>their
>>>>>>>policy, they only have a 90 day warranty!!!
>>>>>>>
>>>>>>>James
>>>>>>>
>>>>>>>"Jon Jiles" <snoid@sheboygan.com> wrote:
>>>>>>>>
>>>>>>>>Hi,
>>>>>>>>
>>>>>>>>Anyone here actually had any real hands on with this board/controller,
>>>>>>especially
>>>>>>>>with Cubase 4? James got me intrigued but I have read that the build
>>>>quolity
>>>>>>>>may be somewhat on cheesy side.
>>>>>>>>
>>>>>>>>Thanks,
>>>>>>>>Jon
>>>>>>>
>>>>>>
>>>>>
>>>>
>>>
>>
>
|
|
|
|
| Re: Any Tascam 3200/4800 users here?...YES!!! [message #79334 is a reply to message #79193] |
Wed, 31 January 2007 14:14 |
Jon Jiles
Messages: 90
Registered: November 2005
|
Member |
|
|
Hi LaMont,
Yup, the firewire seems very interesting (32 in/32 out@ 96k) but the MKII's
not out yet. Apparently some people have tried / are using a firmware updated
version of the firewire card that was originally intended for the DM-24.
If I do this I will stick to the HD9652 for now.
How dangerous do you think it would be to consider the DM3200 used?.. and
what do you think it should be worth?
Cheers,
jj
"LaMont" <jjdpro@ameritech.net> wrote:
>
>Hey Jon,
>
>- most DM24 users/owners units have been rock solid
>- having stated the above, Yamaha Desks are as solid as they come. They
rarley
>break down. O2rs(orignals) are still cranking to this day.
>
>Have you considerd the Firewire Option? 32/32 ins/outs?
>
>"Jon Jiles" <nojij@yahoo.com> wrote:
>>
>>Thanks LaMont -
>>
>>I had considered keeping some of my Paris rig to use as a glorified mastering
>>deck. Sounds like that's what you're suggesting here as a possible solution.
>>
>>I just finished talking to guy who is selling his 02r96v2 (which I've now
>>determined is way out of my price range - even used) and he shared an absolute
>>Tascam customer service horror story regarding a DM-24 he owned. 4 bad
power
>>supplies, LCD failed, lost studio time (had to ship it back something like
>>6 times - from Hawaii!!!!) and Tascam apparently never did make it right
>>for him.
>>
>>Hopefully they got it right with the new boards because the resounding
impression
>>I'm getting of Tascam's willingness/ability to stand behind their products
>>is the only thing causing hesitation for me right now.
>>
>>Cheers,
>>Jon
>>
>>"LaMont " <jjdpro@ameritech.net> wrote:
>>>
>>>Hey Jon,
>>>
>>>Trust me, the marriage of the Tascam 3200 & Cuabse 4 is a match made in
>>heaven.
>>>You will not miss the Paris sound.
>>>
>>>However to not throw away your Paris investment(s), instead of summing
>out
>>>of the 3200..you can...
>>>
>>>Another way.. 3200 out via SP/Dif. into Paris Mec/442 SP/dif..for just
>a
>>>stereo sum .. Again, good sound.
>>>
>>>3200 master (analog outs) into Paris MEC/442.. 24bit(input Card)..then
>24bit
>>>out card..to master or internal bounce..
>>>
>>>You can't loose either way you go.. Grat choice!!
>>>P.S. Put into an Argosy!!! :)
>>>take care.
>>>
>>>- 3200 out (Adat x 2) 16 lightpipes stems into MEC (with 2 adat cards)..
>>>For stem mixing. Very cool.. Very good sound. and provides a means of
Matering
>>>within Paris.
>>>
>>>"Jon Jiles" <nojij@yahoo.com> wrote:
>>>>
>>>>Wow!!!!
>>>>
>>>>That's a pretty ringing endorsement LaMont!!!!
>>>>
>>>>I'm definitely leaning towards the 3200 and Cubase 4. The only client
>in
>>>>my studio is me and I'm really just trying to get to a simpler workflow
>>>,for
>>>>the songwriting end of things, and still achieve quality results at the
>>>end
>>>>of the process.
>>>>
>>>>Can you eplain to me in a little more detail how you (and apparently
BT)
>>>>would be/are using Paris as the master summing mixer/recorder in this
>scenario?
>>>>
>>>>I've currently got Cubase SX3 lightpiped into Paris via a RME 9652 (
a
>>mini-Deej
>>>>set-up if, you will) but being a guy who only gets to work on my stuff
>>in
>>>>the evenings after work or on the weekends, the opportunity for confusion
>>>>in such a kludge ridden set-up doesn't lend itself to the creative workflow.
>>>>That's why Cubase and a nice board/control surface appeals. My big dilemma
>>>>though is that I still absolutely love the way Paris sounds.
>>>>
>>>>Anyway, thanks a ton for the input, greatly appreciated! I've got much
>>to
>>>>consider.
>>>>
>>>>Cheers,
>>>>jon
>>>>
>>>>
>>>>"LaMont" <jjdpro@ameritech.net> wrote:
>>>>>
>>>>>Hi Jon, I can chime in here on this question.
>>>>>
>>>>>I often work at a local studio http://www.lamourrecording.com/
>>>>>which has (2) Yamaha's DM2000. I can't speak highly enough of these
powerful
>>>>>beast.
>>>>>
>>>>>Great feel, 96 channels @ 96K
>>>>>Pro Tools, Neundo/Cubase/Sonar/Logic Controller
>>>>>Nice Comps/EQs on every channel
>>>>>(8) SPX-1000's DSP processors (REVerbs, Delays, Chorus.etc)
>>>>>Some of the sweetest (24) Mic pres you'll find
>>>>>All in a foot print that keeps the Engineer/Operator right in
>>>>>front of the mix..There's a ton more features..
>>>>>
>>>>>I had a chance (2years) ago to take the then Tascam 3200 for week session
>>>>>spin. Due to the fact that no body in our area had a O2r/96, we rented
>>>>>the tascam.. Man, to my ears and others, the Tascam delivers the goods.
>>>>I
>>>>>would have to say that the Tascam 3200 sonics was more "thick" than
the
>>>>DM2000.
>>>>>Different converters and clocks.. But, we mananged to get thru a sesion
>>>>without
>>>>>opening the manual!!
>>>>>You're not going to do that with the Yammys.. he 3200 had full eq and
>>dynamics
>>>>>on every channel as well as I think 4 DSP processors for Verbs and dleays
>>>>>chorus FX.. The verbs were the star of this board. The algo's were from
>>>>TC!!
>>>>>the verb masters. Man, these verbs sounded like our TC 3000 ..really!!.
>>>>The
>>>>>Eqs were usuable as are the Comps/Lim..We click on the DAW controller
>>layer
>>>>>button, scrolled to the DAW template (Pro Tools)..Boom!! "Houston We
>have
>>>>>Controll".. That easy.. We had transport, channel faders and Master
faders
>>>>>and edit scroll.. To be honest, we probable had more functions,but like
>>>>I
>>>>>stated earlier, we had not read the manual..
>>>>>Oh well.
>>>>>
>>>>>Like I told James, I'm looking seriously @ the DM4800 X2 for my Home
>studio..To
>>>>>host Both Nuendo & Pro Tools...AND yes, Liek BrianT does in Houston,
>Paris
>>>>>will be used a he master summing mixer/recorder..
>>>>>
>>>>>The DM3200/4800 can't be beat in their price range. They have the sound,
>>>>>looks, and product maturity. Tascam knew they had a winner with the
DM24,then
>>>>>knocked the ball out of the park with the DM3200, and now DM 4800..
>>>>>
>>>>>Now that it's official that Mackie has dropped the Ball with the DXB(20K
>>>>>Plus), now selling are drastic discounts. The DXB is a one sweet sounding
>>>>>board as well. At 9k it competes very well with Yammys O2r/96..But,
(2)
>>>>x
>>>>>DM4800 @ around is just as and (imo) more potent ..AND dropped in a
cool
>>>>>Argosy, BAMM!..
>>>>>
>>>>>http://www.argosyconsole.com/dm3200.htm
>>>>>
>>>>>
>>>>>
>>>>>"Jon Jiles" <nanaheyhey@no.com> wrote:
>>>>>>
>>>>>>Thanks for all the info James!
>>>>>>
>>>>>>How do they stack up against the Yamaha boards? (O2r96v2 and the DM1000v2,etc)
>>>>>>Also, Cubase implementation will be a key factor if I move from Paris.
>>>>I
>>>>>>will consider the Yamaha boards too (used though due to price) because
>>>>of
>>>>>>the Yammy/Steinberg connection and better Cubase implementation I would
>>>>>suppose.
>>>>>>The Tascam boards do seem like a very good value though... especially
>>>if
>>>>>>they don't break and are not horribly non-intuitive.
>>>>>>
>>>>>>Thanks again,
>>>>>>Jon
>>>>>>
>>>>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>>>>
>>>>>>>By the way, the mic pres on the DM-32 and DM-48 are greatly improved
>>>and
>>>>>>vary
>>>>>>>usable. It was only the DM-24 that had the problems.
>>>>>>>
>>>>>>>James
>>>>>>>
>>>>>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>>>>>
>>>>>>>>Hey Jon!
>>>>>>>>
>>>>>>>>Some of the guys on the DA7 NG have switched to the Tascam DM 32s.
>>
>>>A
>>>>>customer
>>>>>>>>of mine also has one. The mixes from both source sound good. You
>>should
>>>>>>>>always test drive before you buy. You have to like it. I would
think
>>>>>>twice
>>>>>>>>before buying a DM-24, the Mic pres were not so good, they had low
>>head
>>>>>>>room.
>>>>>>>> If you use the DM-24 for line ins only, I think you'd be Ok. There
>>>>was
>>>>>>>>an upgrade for the mic pres through Tascam, they may no longer be
>doing
>>>>>>>that.
>>>>>>>>
>>>>>>>>I hear the DM manuals are terrible, you can go down load them. If
>>you
>>>>>>buy
>>>>>>>>one, make sure you have 30 full days to test it. Clear your planner
>>>>for
>>>>>>>>test time. Read the manual in advance and go to the NG a lot before
>>>>you
>>>>>>>>get it. Every once in awhile Tascam puts out a lemon, so you want
>>to
>>>>>be
>>>>>>>>able to fully test what you buy from them. Unless they have changed
>>>>their
>>>>>>>>policy, they only have a 90 day warranty!!!
>>>>>>>>
>>>>>>>>James
>>>>>>>>
>>>>>>>>"Jon Jiles" <snoid@sheboygan.com> wrote:
>>>>>>>>>
>>>>>>>>>Hi,
>>>>>>>>>
>>>>>>>>>Anyone here actually had any real hands on with this board/controller,
>>>>>>>especially
>>>>>>>>>with Cubase 4? James got me intrigued but I have read that the build
>>>>>quolity
>>>>>>>>>may be somewhat on cheesy side.
>>>>>>>>>
>>>>>>>>>Thanks,
>>>>>>>>>Jon
>>>>>>>>
>>>>>>>
>>>>>>
>>>>>
>>>>
>>>
>>
>
|
|
|
|
| Re: Any Tascam 3200/4800 users here?...YES!!! [message #79335 is a reply to message #79334] |
Wed, 31 January 2007 15:06 |
LaMont
Messages: 828
Registered: October 2005
|
Senior Member |
|
|
James Mc is a Dealer maybe he could chime in. Ok. How old is it?
"Jon Jiles" <nojij@yahoo.com> wrote:
>
>Hi LaMont,
>
>Yup, the firewire seems very interesting (32 in/32 out@ 96k) but the MKII's
>not out yet. Apparently some people have tried / are using a firmware updated
>version of the firewire card that was originally intended for the DM-24.
>
>If I do this I will stick to the HD9652 for now.
>
>How dangerous do you think it would be to consider the DM3200 used?.. and
>what do you think it should be worth?
>
>Cheers,
>jj
>
> "LaMont" <jjdpro@ameritech.net> wrote:
>>
>>Hey Jon,
>>
>>- most DM24 users/owners units have been rock solid
>>- having stated the above, Yamaha Desks are as solid as they come. They
>rarley
>>break down. O2rs(orignals) are still cranking to this day.
>>
>>Have you considerd the Firewire Option? 32/32 ins/outs?
>>
>>"Jon Jiles" <nojij@yahoo.com> wrote:
>>>
>>>Thanks LaMont -
>>>
>>>I had considered keeping some of my Paris rig to use as a glorified mastering
>>>deck. Sounds like that's what you're suggesting here as a possible solution.
>>>
>>>I just finished talking to guy who is selling his 02r96v2 (which I've
now
>>>determined is way out of my price range - even used) and he shared an
absolute
>>>Tascam customer service horror story regarding a DM-24 he owned. 4 bad
>power
>>>supplies, LCD failed, lost studio time (had to ship it back something
like
>>>6 times - from Hawaii!!!!) and Tascam apparently never did make it right
>>>for him.
>>>
>>>Hopefully they got it right with the new boards because the resounding
>impression
>>>I'm getting of Tascam's willingness/ability to stand behind their products
>>>is the only thing causing hesitation for me right now.
>>>
>>>Cheers,
>>>Jon
>>>
>>>"LaMont " <jjdpro@ameritech.net> wrote:
>>>>
>>>>Hey Jon,
>>>>
>>>>Trust me, the marriage of the Tascam 3200 & Cuabse 4 is a match made
in
>>>heaven.
>>>>You will not miss the Paris sound.
>>>>
>>>>However to not throw away your Paris investment(s), instead of summing
>>out
>>>>of the 3200..you can...
>>>>
>>>>Another way.. 3200 out via SP/Dif. into Paris Mec/442 SP/dif..for just
>>a
>>>>stereo sum .. Again, good sound.
>>>>
>>>>3200 master (analog outs) into Paris MEC/442.. 24bit(input Card)..then
>>24bit
>>>>out card..to master or internal bounce..
>>>>
>>>>You can't loose either way you go.. Grat choice!!
>>>>P.S. Put into an Argosy!!! :)
>>>>take care.
>>>>
>>>>- 3200 out (Adat x 2) 16 lightpipes stems into MEC (with 2 adat cards)..
>>>>For stem mixing. Very cool.. Very good sound. and provides a means of
>Matering
>>>>within Paris.
>>>>
>>>>"Jon Jiles" <nojij@yahoo.com> wrote:
>>>>>
>>>>>Wow!!!!
>>>>>
>>>>>That's a pretty ringing endorsement LaMont!!!!
>>>>>
>>>>>I'm definitely leaning towards the 3200 and Cubase 4. The only client
>>in
>>>>>my studio is me and I'm really just trying to get to a simpler workflow
>>>>,for
>>>>>the songwriting end of things, and still achieve quality results at
the
>>>>end
>>>>>of the process.
>>>>>
>>>>>Can you eplain to me in a little more detail how you (and apparently
>BT)
>>>>>would be/are using Paris as the master summing mixer/recorder in this
>>scenario?
>>>>>
>>>>>I've currently got Cubase SX3 lightpiped into Paris via a RME 9652 (
>a
>>>mini-Deej
>>>>>set-up if, you will) but being a guy who only gets to work on my stuff
>>>in
>>>>>the evenings after work or on the weekends, the opportunity for confusion
>>>>>in such a kludge ridden set-up doesn't lend itself to the creative workflow.
>>>>>That's why Cubase and a nice board/control surface appeals. My big dilemma
>>>>>though is that I still absolutely love the way Paris sounds.
>>>>>
>>>>>Anyway, thanks a ton for the input, greatly appreciated! I've got much
>>>to
>>>>>consider.
>>>>>
>>>>>Cheers,
>>>>>jon
>>>>>
>>>>>
>>>>>"LaMont" <jjdpro@ameritech.net> wrote:
>>>>>>
>>>>>>Hi Jon, I can chime in here on this question.
>>>>>>
>>>>>>I often work at a local studio http://www.lamourrecording.com/
>>>>>>which has (2) Yamaha's DM2000. I can't speak highly enough of these
>powerful
>>>>>>beast.
>>>>>>
>>>>>>Great feel, 96 channels @ 96K
>>>>>>Pro Tools, Neundo/Cubase/Sonar/Logic Controller
>>>>>>Nice Comps/EQs on every channel
>>>>>>(8) SPX-1000's DSP processors (REVerbs, Delays, Chorus.etc)
>>>>>>Some of the sweetest (24) Mic pres you'll find
>>>>>>All in a foot print that keeps the Engineer/Operator right in
>>>>>>front of the mix..There's a ton more features..
>>>>>>
>>>>>>I had a chance (2years) ago to take the then Tascam 3200 for week session
>>>>>>spin. Due to the fact that no body in our area had a O2r/96, we rented
>>>>>>the tascam.. Man, to my ears and others, the Tascam delivers the goods.
>>>>>I
>>>>>>would have to say that the Tascam 3200 sonics was more "thick" than
>the
>>>>>DM2000.
>>>>>>Different converters and clocks.. But, we mananged to get thru a sesion
>>>>>without
>>>>>>opening the manual!!
>>>>>>You're not going to do that with the Yammys.. he 3200 had full eq and
>>>dynamics
>>>>>>on every channel as well as I think 4 DSP processors for Verbs and
dleays
>>>>>>chorus FX.. The verbs were the star of this board. The algo's were
from
>>>>>TC!!
>>>>>>the verb masters. Man, these verbs sounded like our TC 3000 ..really!!.
>>>>>The
>>>>>>Eqs were usuable as are the Comps/Lim..We click on the DAW controller
>>>layer
>>>>>>button, scrolled to the DAW template (Pro Tools)..Boom!! "Houston We
>>have
>>>>>>Controll".. That easy.. We had transport, channel faders and Master
>faders
>>>>>>and edit scroll.. To be honest, we probable had more functions,but
like
>>>>>I
>>>>>>stated earlier, we had not read the manual..
>>>>>>Oh well.
>>>>>>
>>>>>>Like I told James, I'm looking seriously @ the DM4800 X2 for my Home
>>studio..To
>>>>>>host Both Nuendo & Pro Tools...AND yes, Liek BrianT does in Houston,
>>Paris
>>>>>>will be used a he master summing mixer/recorder..
>>>>>>
>>>>>>The DM3200/4800 can't be beat in their price range. They have the sound,
>>>>>>looks, and product maturity. Tascam knew they had a winner with the
>DM24,then
>>>>>>knocked the ball out of the park with the DM3200, and now DM 4800..
>
>>>>>>
>>>>>>Now that it's official that Mackie has dropped the Ball with the DXB(20K
>>>>>>Plus), now selling are drastic discounts. The DXB is a one sweet sounding
>>>>>>board as well. At 9k it competes very well with Yammys O2r/96..But,
>(2)
>>>>>x
>>>>>>DM4800 @ around is just as and (imo) more potent ..AND dropped in a
>cool
>>>>>>Argosy, BAMM!..
>>>>>>
>>>>>>http://www.argosyconsole.com/dm3200.htm
>>>>>>
>>>>>>
>>>>>>
>>>>>>"Jon Jiles" <nanaheyhey@no.com> wrote:
>>>>>>>
>>>>>>>Thanks for all the info James!
>>>>>>>
>>>>>>>How do they stack up against the Yamaha boards? (O2r96v2 and the DM1000v2,etc)
>>>>>>>Also, Cubase implementation will be a key factor if I move from Paris.
>>>>>I
>>>>>>>will consider the Yamaha boards too (used though due to price) because
>>>>>of
>>>>>>>the Yammy/Steinberg connection and better Cubase implementation I
would
>>>>>>suppose.
>>>>>>>The Tascam boards do seem like a very good value though... especially
>>>>if
>>>>>>>they don't break and are not horribly non-intuitive.
>>>>>>>
>>>>>>>Thanks again,
>>>>>>>Jon
>>>>>>>
>>>>>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>>>>>
>>>>>>>>By the way, the mic pres on the DM-32 and DM-48 are greatly improved
>>>>and
>>>>>>>vary
>>>>>>>>usable. It was only the DM-24 that had the problems.
>>>>>>>>
>>>>>>>>James
>>>>>>>>
>>>>>>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>>>>>>
>>>>>>>>>Hey Jon!
>>>>>>>>>
>>>>>>>>>Some of the guys on the DA7 NG have switched to the Tascam DM 32s.
>>>
>>>>A
>>>>>>customer
>>>>>>>>>of mine also has one. The mixes from both source sound good. You
>>>should
>>>>>>>>>always test drive before you buy. You have to like it. I would
>think
>>>>>>>twice
>>>>>>>>>before buying a DM-24, the Mic pres were not so good, they had low
>>>head
>>>>>>>>room.
>>>>>>>>> If you use the DM-24 for line ins only, I think you'd be Ok. There
>>>>>was
>>>>>>>>>an upgrade for the mic pres through Tascam, they may no longer be
>>doing
>>>>>>>>that.
>>>>>>>>>
>>>>>>>>>I hear the DM manuals are terrible, you can go down load them.
If
>>>you
>>>>>>>buy
>>>>>>>>>one, make sure you have 30 full days to test it. Clear your planner
>>>>>for
>>>>>>>>>test time. Read the manual in advance and go to the NG a lot before
>>>>>you
>>>>>>>>>get it. Every once in awhile Tascam puts out a lemon, so you want
>>>to
>>>>>>be
>>>>>>>>>able to fully test what you buy from them. Unless they have changed
>>>>>their
>>>>>>>>>policy, they only have a 90 day warranty!!!
>>>>>>>>>
>>>>>>>>>James
>>>>>>>>>
>>>>>>>>>"Jon Jiles" <snoid@sheboygan.com> wrote:
>>>>>>>>>>
>>>>>>>>>>Hi,
>>>>>>>>>>
>>>>>>>>>>Anyone here actually had any real hands on with this board/controller,
>>>>>>>>especially
>>>>>>>>>>with Cubase 4? James got me intrigued but I have read that the
build
>>>>>>quolity
>>>>>>>>>>may be somewhat on cheesy side.
>>>>>>>>>>
>>>>>>>>>>Thanks,
>>>>>>>>>>Jon
>>>>>>>>>
>>>>>>>>
>>>>>>>
>>>>>>
>>>>>
>>>>
>>>
>>
>
|
|
|
|
| Re: Any Tascam 3200/4800 users here?...YES!!! [message #79336 is a reply to message #79334] |
Wed, 31 January 2007 16:04 |
excelav
Messages: 2130
Registered: July 2005
Location: Metro Detroit
|
Senior Member |
|
|
Hey Jon, when I mentioned the DMs, I was thinking with the FW card. The DM
becomes your computer audio interface, control surface, routing matrix, your
digital format converters, mixer, multi effects, dynamic effects, Eq, Que/talk
back system, summing box, possibly your automation and it looks cool. With
out the FW card it doesn't make as much sense.
I have never seen these used, and I've been looking. I've seen DM-24s as
low as $500.00, but your looking at a 1999 vintage board design. I question
the quality of the mic pres and they were known for having the LCD screens
go bad. I think it would be Ok if you could buy a DM-32 used from a local
store and try it out for 30 days.
James
"Jon Jiles" <nojij@yahoo.com> wrote:
>
>Hi LaMont,
>
>Yup, the firewire seems very interesting (32 in/32 out@ 96k) but the MKII's
>not out yet. Apparently some people have tried / are using a firmware updated
>version of the firewire card that was originally intended for the DM-24.
>
>If I do this I will stick to the HD9652 for now.
>
>How dangerous do you think it would be to consider the DM3200 used?.. and
>what do you think it should be worth?
>
>Cheers,
>jj
>
> "LaMont" <jjdpro@ameritech.net> wrote:
>>
>>Hey Jon,
>>
>>- most DM24 users/owners units have been rock solid
>>- having stated the above, Yamaha Desks are as solid as they come. They
>rarley
>>break down. O2rs(orignals) are still cranking to this day.
>>
>>Have you considerd the Firewire Option? 32/32 ins/outs?
>>
>>"Jon Jiles" <nojij@yahoo.com> wrote:
>>>
>>>Thanks LaMont -
>>>
>>>I had considered keeping some of my Paris rig to use as a glorified mastering
>>>deck. Sounds like that's what you're suggesting here as a possible solution.
>>>
>>>I just finished talking to guy who is selling his 02r96v2 (which I've
now
>>>determined is way out of my price range - even used) and he shared an
absolute
>>>Tascam customer service horror story regarding a DM-24 he owned. 4 bad
>power
>>>supplies, LCD failed, lost studio time (had to ship it back something
like
>>>6 times - from Hawaii!!!!) and Tascam apparently never did make it right
>>>for him.
>>>
>>>Hopefully they got it right with the new boards because the resounding
>impression
>>>I'm getting of Tascam's willingness/ability to stand behind their products
>>>is the only thing causing hesitation for me right now.
>>>
>>>Cheers,
>>>Jon
>>>
>>>"LaMont " <jjdpro@ameritech.net> wrote:
>>>>
>>>>Hey Jon,
>>>>
>>>>Trust me, the marriage of the Tascam 3200 & Cuabse 4 is a match made
in
>>>heaven.
>>>>You will not miss the Paris sound.
>>>>
>>>>However to not throw away your Paris investment(s), instead of summing
>>out
>>>>of the 3200..you can...
>>>>
>>>>Another way.. 3200 out via SP/Dif. into Paris Mec/442 SP/dif..for just
>>a
>>>>stereo sum .. Again, good sound.
>>>>
>>>>3200 master (analog outs) into Paris MEC/442.. 24bit(input Card)..then
>>24bit
>>>>out card..to master or internal bounce..
>>>>
>>>>You can't loose either way you go.. Grat choice!!
>>>>P.S. Put into an Argosy!!! :)
>>>>take care.
>>>>
>>>>- 3200 out (Adat x 2) 16 lightpipes stems into MEC (with 2 adat cards)..
>>>>For stem mixing. Very cool.. Very good sound. and provides a means of
>Matering
>>>>within Paris.
>>>>
>>>>"Jon Jiles" <nojij@yahoo.com> wrote:
>>>>>
>>>>>Wow!!!!
>>>>>
>>>>>That's a pretty ringing endorsement LaMont!!!!
>>>>>
>>>>>I'm definitely leaning towards the 3200 and Cubase 4. The only client
>>in
>>>>>my studio is me and I'm really just trying to get to a simpler workflow
>>>>,for
>>>>>the songwriting end of things, and still achieve quality results at
the
>>>>end
>>>>>of the process.
>>>>>
>>>>>Can you eplain to me in a little more detail how you (and apparently
>BT)
>>>>>would be/are using Paris as the master summing mixer/recorder in this
>>scenario?
>>>>>
>>>>>I've currently got Cubase SX3 lightpiped into Paris via a RME 9652 (
>a
>>>mini-Deej
>>>>>set-up if, you will) but being a guy who only gets to work on my stuff
>>>in
>>>>>the evenings after work or on the weekends, the opportunity for confusion
>>>>>in such a kludge ridden set-up doesn't lend itself to the creative workflow.
>>>>>That's why Cubase and a nice board/control surface appeals. My big dilemma
>>>>>though is that I still absolutely love the way Paris sounds.
>>>>>
>>>>>Anyway, thanks a ton for the input, greatly appreciated! I've got much
>>>to
>>>>>consider.
>>>>>
>>>>>Cheers,
>>>>>jon
>>>>>
>>>>>
>>>>>"LaMont" <jjdpro@ameritech.net> wrote:
>>>>>>
>>>>>>Hi Jon, I can chime in here on this question.
>>>>>>
>>>>>>I often work at a local studio http://www.lamourrecording.com/
>>>>>>which has (2) Yamaha's DM2000. I can't speak highly enough of these
>powerful
>>>>>>beast.
>>>>>>
>>>>>>Great feel, 96 channels @ 96K
>>>>>>Pro Tools, Neundo/Cubase/Sonar/Logic Controller
>>>>>>Nice Comps/EQs on every channel
>>>>>>(8) SPX-1000's DSP processors (REVerbs, Delays, Chorus.etc)
>>>>>>Some of the sweetest (24) Mic pres you'll find
>>>>>>All in a foot print that keeps the Engineer/Operator right in
>>>>>>front of the mix..There's a ton more features..
>>>>>>
>>>>>>I had a chance (2years) ago to take the then Tascam 3200 for week session
>>>>>>spin. Due to the fact that no body in our area had a O2r/96, we rented
>>>>>>the tascam.. Man, to my ears and others, the Tascam delivers the goods.
>>>>>I
>>>>>>would have to say that the Tascam 3200 sonics was more "thick" than
>the
>>>>>DM2000.
>>>>>>Different converters and clocks.. But, we mananged to get thru a sesion
>>>>>without
>>>>>>opening the manual!!
>>>>>>You're not going to do that with the Yammys.. he 3200 had full eq and
>>>dynamics
>>>>>>on every channel as well as I think 4 DSP processors for Verbs and
dleays
>>>>>>chorus FX.. The verbs were the star of this board. The algo's were
from
>>>>>TC!!
>>>>>>the verb masters. Man, these verbs sounded like our TC 3000 ..really!!.
>>>>>The
>>>>>>Eqs were usuable as are the Comps/Lim..We click on the DAW controller
>>>layer
>>>>>>button, scrolled to the DAW template (Pro Tools)..Boom!! "Houston We
>>have
>>>>>>Controll".. That easy.. We had transport, channel faders and Master
>faders
>>>>>>and edit scroll.. To be honest, we probable had more functions,but
like
>>>>>I
>>>>>>stated earlier, we had not read the manual..
>>>>>>Oh well.
>>>>>>
>>>>>>Like I told James, I'm looking seriously @ the DM4800 X2 for my Home
>>studio..To
>>>>>>host Both Nuendo & Pro Tools...AND yes, Liek BrianT does in Houston,
>>Paris
>>>>>>will be used a he master summing mixer/recorder..
>>>>>>
>>>>>>The DM3200/4800 can't be beat in their price range. They have the sound,
>>>>>>looks, and product maturity. Tascam knew they had a winner with the
>DM24,then
>>>>>>knocked the ball out of the park with the DM3200, and now DM 4800..
>
>>>>>>
>>>>>>Now that it's official that Mackie has dropped the Ball with the DXB(20K
>>>>>>Plus), now selling are drastic discounts. The DXB is a one sweet sounding
>>>>>>board as well. At 9k it competes very well with Yammys O2r/96..But,
>(2)
>>>>>x
>>>>>>DM4800 @ around is just as and (imo) more potent ..AND dropped in a
>cool
>>>>>>Argosy, BAMM!..
>>>>>>
>>>>>>http://www.argosyconsole.com/dm3200.htm
>>>>>>
>>>>>>
>>>>>>
>>>>>>"Jon Jiles" <nanaheyhey@no.com> wrote:
>>>>>>>
>>>>>>>Thanks for all the info James!
>>>>>>>
>>>>>>>How do they stack up against the Yamaha boards? (O2r96v2 and the DM1000v2,etc)
>>>>>>>Also, Cubase implementation will be a key factor if I move from Paris.
>>>>>I
>>>>>>>will consider the Yamaha boards too (used though due to price) because
>>>>>of
>>>>>>>the Yammy/Steinberg connection and better Cubase implementation I
would
>>>>>>suppose.
>>>>>>>The Tascam boards do seem like a very good value though... especially
>>>>if
>>>>>>>they don't break and are not horribly non-intuitive.
>>>>>>>
>>>>>>>Thanks again,
>>>>>>>Jon
>>>>>>>
>>>>>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>>>>>
>>>>>>>>By the way, the mic pres on the DM-32 and DM-48 are greatly improved
>>>>and
>>>>>>>vary
>>>>>>>>usable. It was only the DM-24 that had the problems.
>>>>>>>>
>>>>>>>>James
>>>>>>>>
>>>>>>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>>>>>>
>>>>>>>>>Hey Jon!
>>>>>>>>>
>>>>>>>>>Some of the guys on the DA7 NG have switched to the Tascam DM 32s.
>>>
>>>>A
>>>>>>customer
>>>>>>>>>of mine also has one. The mixes from both source sound good. You
>>>should
>>>>>>>>>always test drive before you buy. You have to like it. I would
>think
>>>>>>>twice
>>>>>>>>>before buying a DM-24, the Mic pres were not so good, they had low
>>>head
>>>>>>>>room.
>>>>>>>>> If you use the DM-24 for line ins only, I think you'd be Ok. There
>>>>>was
>>>>>>>>>an upgrade for the mic pres through Tascam, they may no longer be
>>doing
>>>>>>>>that.
>>>>>>>>>
>>>>>>>>>I hear the DM manuals are terrible, you can go down load them.
If
>>>you
>>>>>>>buy
>>>>>>>>>one, make sure you have 30 full days to test it. Clear your planner
>>>>>for
>>>>>>>>>test time. Read the manual in advance and go to the NG a lot before
>>>>>you
>>>>>>>>>get it. Every once in awhile Tascam puts out a lemon, so you want
>>>to
>>>>>>be
>>>>>>>>>able to fully test what you buy from them. Unless they have changed
>>>>>their
>>>>>>>>>policy, they only have a 90 day warranty!!!
>>>>>>>>>
>>>>>>>>>James
>>>>>>>>>
>>>>>>>>>"Jon Jiles" <snoid@sheboygan.com> wrote:
>>>>>>>>>>
>>>>>>>>>>Hi,
>>>>>>>>>>
>>>>>>>>>>Anyone here actually had any real hands on with this board/controller,
>>>>>>>>especially
>>>>>>>>>>with Cubase 4? James got me intrigued but I have read that the
build
>>>>>>quolity
>>>>>>>>>>may be somewhat on cheesy side.
>>>>>>>>>>
>>>>>>>>>>Thanks,
>>>>>>>>>>Jon
>>>>>>>>>
>>>>>>>>
>>>>>>>
>>>>>>
>>>>>
>>>>
>>>
>>
>
|
|
|
|
| Attn: Jon Jiles, Tascam 3200/4800 [message #79424 is a reply to message #79334] |
Fri, 02 February 2007 15:59 |
excelav
Messages: 2130
Registered: July 2005
Location: Metro Detroit
|
Senior Member |
|
|
Hey Jon! There is a Tascam DM-3200 with a FW card about to go on ebay for
$2000.00. It's in Chicago and shipping is $97.00.
here are the links:
http://cgi.ebay.com/TASCAM-DM-3200-Digital-Mixing-Firewire-o ption_W0QQitemZ180080107203QQihZ008QQcategoryZ23785QQssPageN ameZWDVWQQrdZ1QQcmdZViewItem
http://search.ebay.com/Tascam-DM-3200_W0QQcatrefZC6QQcoactio nZcompareQQcoentrypageZsearchQQcopagenumZ1QQfclZ3QQfromZR9QQ fromZR9QQfrppZ50QQfsooZ1QQfsopZ1QQfstypeZ1QQftrtZ1QQftrvZ1QQ sacatZQ2d1QQsacurZ0QQsaslopZ1QQsatitleZTascamQ20DMQ2d3200QQs spagenameZSTRKQ3aMEFSRCHQ3aSRCH
James
"Jon Jiles" <nojij@yahoo.com> wrote:
>
>Hi LaMont,
>
>Yup, the firewire seems very interesting (32 in/32 out@ 96k) but the MKII's
>not out yet. Apparently some people have tried / are using a firmware updated
>version of the firewire card that was originally intended for the DM-24.
>
>If I do this I will stick to the HD9652 for now.
>
>How dangerous do you think it would be to consider the DM3200 used?.. and
>what do you think it should be worth?
>
>Cheers,
>jj
>
> "LaMont" <jjdpro@ameritech.net> wrote:
>>
>>Hey Jon,
>>
>>- most DM24 users/owners units have been rock solid
>>- having stated the above, Yamaha Desks are as solid as they come. They
>rarley
>>break down. O2rs(orignals) are still cranking to this day.
>>
>>Have you considerd the Firewire Option? 32/32 ins/outs?
>>
>>"Jon Jiles" <nojij@yahoo.com> wrote:
>>>
>>>Thanks LaMont -
>>>
>>>I had considered keeping some of my Paris rig to use as a glorified mastering
>>>deck. Sounds like that's what you're suggesting here as a possible solution.
>>>
>>>I just finished talking to guy who is selling his 02r96v2 (which I've
now
>>>determined is way out of my price range - even used) and he shared an
absolute
>>>Tascam customer service horror story regarding a DM-24 he owned. 4 bad
>power
>>>supplies, LCD failed, lost studio time (had to ship it back something
like
>>>6 times - from Hawaii!!!!) and Tascam apparently never did make it right
>>>for him.
>>>
>>>Hopefully they got it right with the new boards because the resounding
>impression
>>>I'm getting of Tascam's willingness/ability to stand behind their products
>>>is the only thing causing hesitation for me right now.
>>>
>>>Cheers,
>>>Jon
>>>
>>>"LaMont " <jjdpro@ameritech.net> wrote:
>>>>
>>>>Hey Jon,
>>>>
>>>>Trust me, the marriage of the Tascam 3200 & Cuabse 4 is a match made
in
>>>heaven.
>>>>You will not miss the Paris sound.
>>>>
>>>>However to not throw away your Paris investment(s), instead of summing
>>out
>>>>of the 3200..you can...
>>>>
>>>>Another way.. 3200 out via SP/Dif. into Paris Mec/442 SP/dif..for just
>>a
>>>>stereo sum .. Again, good sound.
>>>>
>>>>3200 master (analog outs) into Paris MEC/442.. 24bit(input Card)..then
>>24bit
>>>>out card..to master or internal bounce..
>>>>
>>>>You can't loose either way you go.. Grat choice!!
>>>>P.S. Put into an Argosy!!! :)
>>>>take care.
>>>>
>>>>- 3200 out (Adat x 2) 16 lightpipes stems into MEC (with 2 adat cards)..
>>>>For stem mixing. Very cool.. Very good sound. and provides a means of
>Matering
>>>>within Paris.
>>>>
>>>>"Jon Jiles" <nojij@yahoo.com> wrote:
>>>>>
>>>>>Wow!!!!
>>>>>
>>>>>That's a pretty ringing endorsement LaMont!!!!
>>>>>
>>>>>I'm definitely leaning towards the 3200 and Cubase 4. The only client
>>in
>>>>>my studio is me and I'm really just trying to get to a simpler workflow
>>>>,for
>>>>>the songwriting end of things, and still achieve quality results at
the
>>>>end
>>>>>of the process.
>>>>>
>>>>>Can you eplain to me in a little more detail how you (and apparently
>BT)
>>>>>would be/are using Paris as the master summing mixer/recorder in this
>>scenario?
>>>>>
>>>>>I've currently got Cubase SX3 lightpiped into Paris via a RME 9652 (
>a
>>>mini-Deej
>>>>>set-up if, you will) but being a guy who only gets to work on my stuff
>>>in
>>>>>the evenings after work or on the weekends, the opportunity for confusion
>>>>>in such a kludge ridden set-up doesn't lend itself to the creative workflow.
>>>>>That's why Cubase and a nice board/control surface appeals. My big dilemma
>>>>>though is that I still absolutely love the way Paris sounds.
>>>>>
>>>>>Anyway, thanks a ton for the input, greatly appreciated! I've got much
>>>to
>>>>>consider.
>>>>>
>>>>>Cheers,
>>>>>jon
>>>>>
>>>>>
>>>>>"LaMont" <jjdpro@ameritech.net> wrote:
>>>>>>
>>>>>>Hi Jon, I can chime in here on this question.
>>>>>>
>>>>>>I often work at a local studio http://www.lamourrecording.com/
>>>>>>which has (2) Yamaha's DM2000. I can't speak highly enough of these
>powerful
>>>>>>beast.
>>>>>>
>>>>>>Great feel, 96 channels @ 96K
>>>>>>Pro Tools, Neundo/Cubase/Sonar/Logic Controller
>>>>>>Nice Comps/EQs on every channel
>>>>>>(8) SPX-1000's DSP processors (REVerbs, Delays, Chorus.etc)
>>>>>>Some of the sweetest (24) Mic pres you'll find
>>>>>>All in a foot print that keeps the Engineer/Operator right in
>>>>>>front of the mix..There's a ton more features..
>>>>>>
>>>>>>I had a chance (2years) ago to take the then Tascam 3200 for week session
>>>>>>spin. Due to the fact that no body in our area had a O2r/96, we rented
>>>>>>the tascam.. Man, to my ears and others, the Tascam delivers the goods.
>>>>>I
>>>>>>would have to say that the Tascam 3200 sonics was more "thick" than
>the
>>>>>DM2000.
>>>>>>Different converters and clocks.. But, we mananged to get thru a sesion
>>>>>without
>>>>>>opening the manual!!
>>>>>>You're not going to do that with the Yammys.. he 3200 had full eq and
>>>dynamics
>>>>>>on every channel as well as I think 4 DSP processors for Verbs and
dleays
>>>>>>chorus FX.. The verbs were the star of this board. The algo's were
from
>>>>>TC!!
>>>>>>the verb masters. Man, these verbs sounded like our TC 3000 ..really!!.
>>>>>The
>>>>>>Eqs were usuable as are the Comps/Lim..We click on the DAW controller
>>>layer
>>>>>>button, scrolled to the DAW template (Pro Tools)..Boom!! "Houston We
>>have
>>>>>>Controll".. That easy.. We had transport, channel faders and Master
>faders
>>>>>>and edit scroll.. To be honest, we probable had more functions,but
like
>>>>>I
>>>>>>stated earlier, we had not read the manual..
>>>>>>Oh well.
>>>>>>
>>>>>>Like I told James, I'm looking seriously @ the DM4800 X2 for my Home
>>studio..To
>>>>>>host Both Nuendo & Pro Tools...AND yes, Liek BrianT does in Houston,
>>Paris
>>>>>>will be used a he master summing mixer/recorder..
>>>>>>
>>>>>>The DM3200/4800 can't be beat in their price range. They have the sound,
>>>>>>looks, and product maturity. Tascam knew they had a winner with the
>DM24,then
>>>>>>knocked the ball out of the park with the DM3200, and now DM 4800..
>
>>>>>>
>>>>>>Now that it's official that Mackie has dropped the Ball with the DXB(20K
>>>>>>Plus), now selling are drastic discounts. The DXB is a one sweet sounding
>>>>>>board as well. At 9k it competes very well with Yammys O2r/96..But,
>(2)
>>>>>x
>>>>>>DM4800 @ around is just as and (imo) more potent ..AND dropped in a
>cool
>>>>>>Argosy, BAMM!..
>>>>>>
>>>>>>http://www.argosyconsole.com/dm3200.htm
>>>>>>
>>>>>>
>>>>>>
>>>>>>"Jon Jiles" <nanaheyhey@no.com> wrote:
>>>>>>>
>>>>>>>Thanks for all the info James!
>>>>>>>
>>>>>>>How do they stack up against the Yamaha boards? (O2r96v2 and the DM1000v2,etc)
>>>>>>>Also, Cubase implementation will be a key factor if I move from Paris.
>>>>>I
>>>>>>>will consider the Yamaha boards too (used though due to price) because
>>>>>of
>>>>>>>the Yammy/Steinberg connection and better Cubase implementation I
would
>>>>>>suppose.
>>>>>>>The Tascam boards do seem like a very good value though... especially
>>>>if
>>>>>>>they don't break and are not horribly non-intuitive.
>>>>>>>
>>>>>>>Thanks again,
>>>>>>>Jon
>>>>>>>
>>>>>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>>>>>
>>>>>>>>By the way, the mic pres on the DM-32 and DM-48 are greatly improved
>>>>and
>>>>>>>vary
>>>>>>>>usable. It was only the DM-24 that had the problems.
>>>>>>>>
>>>>>>>>James
>>>>>>>>
>>>>>>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>>>>>>
>>>>>>>>>Hey Jon!
>>>>>>>>>
>>>>>>>>>Some of the guys on the DA7 NG have switched to the Tascam DM 32s.
>>>
>>>>A
>>>>>>customer
>>>>>>>>>of mine also has one. The mixes from both source sound good. You
>>>should
>>>>>>>>>always test drive before you buy. You have to like it. I would
>think
>>>>>>>twice
>>>>>>>>>before buying a DM-24, the Mic pres were not so good, they had low
>>>head
>>>>>>>>room.
>>>>>>>>> If you use the DM-24 for line ins only, I think you'd be Ok. There
>>>>>was
>>>>>>>>>an upgrade for the mic pres through Tascam, they may no longer be
>>doing
>>>>>>>>that.
>>>>>>>>>
>>>>>>>>>I hear the DM manuals are terrible, you can go down load them.
If
>>>you
>>>>>>>buy
>>>>>>>>>one, make sure you have 30 full days to test it. Clear your planner
>>>>>for
>>>>>>>>>test time. Read the manual in advance and go to the NG a lot before
>>>>>you
>>>>>>>>>get it. Every once in awhile Tascam puts out a lemon, so you want
>>>to
>>>>>>be
>>>>>>>>>able to fully test what you buy from them. Unless they have changed
>>>>>their
>>>>>>>>>policy, they only have a 90 day warranty!!!
>>>>>>>>>
>>>>>>>>>James
>>>>>>>>>
>>>>>>>>>"Jon Jiles" <snoid@sheboygan.com> wrote:
>>>>>>>>>>
>>>>>>>>>>Hi,
>>>>>>>>>>
>>>>>>>>>>Anyone here actually had any real hands on with this board/controller,
>>>>>>>>especially
>>>>>>>>>>with Cubase 4? James got me intrigued but I have read that the
build
>>>>>>quolity
>>>>>>>>>>may be somewhat on cheesy side.
>>>>>>>>>>
>>>>>>>>>>Thanks,
>>>>>>>>>>Jon
>>>>>>>>>
>>>>>>>>
>>>>>>>
>>>>>>
>>>>>
>>>>
>>>
>>
>
|
|
|
|
| Re: Attn: Jon Jiles, Tascam 3200/4800 [message #79433 is a reply to message #79424] |
Fri, 02 February 2007 23:19 |
Jon Jiles
Messages: 90
Registered: November 2005
|
Member |
|
|
Thanks James. I was all over it actually, but got sniped at the last minute!
Ah well ...
"James McCloskey" <excelsm@hotmail.com> wrote:
>
>Hey Jon! There is a Tascam DM-3200 with a FW card about to go on ebay for
>$2000.00. It's in Chicago and shipping is $97.00.
>
>here are the links:
>
> http://cgi.ebay.com/TASCAM-DM-3200-Digital-Mixing-Firewire-o ption_W0QQitemZ180080107203QQihZ008QQcategoryZ23785QQssPageN ameZWDVWQQrdZ1QQcmdZViewItem
>
> http://search.ebay.com/Tascam-DM-3200_W0QQcatrefZC6QQcoactio nZcompareQQcoentrypageZsearchQQcopagenumZ1QQfclZ3QQfromZR9QQ fromZR9QQfrppZ50QQfsooZ1QQfsopZ1QQfstypeZ1QQftrtZ1QQftrvZ1QQ sacatZQ2d1QQsacurZ0QQsaslopZ1QQsatitleZTascamQ20DMQ2d3200QQs spagenameZSTRKQ3aMEFSRCHQ3aSRCH
>
>James
>
>
>"Jon Jiles" <nojij@yahoo.com> wrote:
>>
>>Hi LaMont,
>>
>>Yup, the firewire seems very interesting (32 in/32 out@ 96k) but the MKII's
>>not out yet. Apparently some people have tried / are using a firmware updated
>>version of the firewire card that was originally intended for the DM-24.
>>
>>If I do this I will stick to the HD9652 for now.
>>
>>How dangerous do you think it would be to consider the DM3200 used?.. and
>>what do you think it should be worth?
>>
>>Cheers,
>>jj
>>
>> "LaMont" <jjdpro@ameritech.net> wrote:
>>>
>>>Hey Jon,
>>>
>>>- most DM24 users/owners units have been rock solid
>>>- having stated the above, Yamaha Desks are as solid as they come. They
>>rarley
>>>break down. O2rs(orignals) are still cranking to this day.
>>>
>>>Have you considerd the Firewire Option? 32/32 ins/outs?
>>>
>>>"Jon Jiles" <nojij@yahoo.com> wrote:
>>>>
>>>>Thanks LaMont -
>>>>
>>>>I had considered keeping some of my Paris rig to use as a glorified mastering
>>>>deck. Sounds like that's what you're suggesting here as a possible solution.
>>>>
>>>>I just finished talking to guy who is selling his 02r96v2 (which I've
>now
>>>>determined is way out of my price range - even used) and he shared an
>absolute
>>>>Tascam customer service horror story regarding a DM-24 he owned. 4 bad
>>power
>>>>supplies, LCD failed, lost studio time (had to ship it back something
>like
>>>>6 times - from Hawaii!!!!) and Tascam apparently never did make it right
>>>>for him.
>>>>
>>>>Hopefully they got it right with the new boards because the resounding
>>impression
>>>>I'm getting of Tascam's willingness/ability to stand behind their products
>>>>is the only thing causing hesitation for me right now.
>>>>
>>>>Cheers,
>>>>Jon
>>>>
>>>>"LaMont " <jjdpro@ameritech.net> wrote:
>>>>>
>>>>>Hey Jon,
>>>>>
>>>>>Trust me, the marriage of the Tascam 3200 & Cuabse 4 is a match made
>in
>>>>heaven.
>>>>>You will not miss the Paris sound.
>>>>>
>>>>>However to not throw away your Paris investment(s), instead of summing
>>>out
>>>>>of the 3200..you can...
>>>>>
>>>>>Another way.. 3200 out via SP/Dif. into Paris Mec/442 SP/dif..for just
>>>a
>>>>>stereo sum .. Again, good sound.
>>>>>
>>>>>3200 master (analog outs) into Paris MEC/442.. 24bit(input Card)..then
>>>24bit
>>>>>out card..to master or internal bounce..
>>>>>
>>>>>You can't loose either way you go.. Grat choice!!
>>>>>P.S. Put into an Argosy!!! :)
>>>>>take care.
>>>>>
>>>>>- 3200 out (Adat x 2) 16 lightpipes stems into MEC (with 2 adat cards)..
>>>>>For stem mixing. Very cool.. Very good sound. and provides a means of
>>Matering
>>>>>within Paris.
>>>>>
>>>>>"Jon Jiles" <nojij@yahoo.com> wrote:
>>>>>>
>>>>>>Wow!!!!
>>>>>>
>>>>>>That's a pretty ringing endorsement LaMont!!!!
>>>>>>
>>>>>>I'm definitely leaning towards the 3200 and Cubase 4. The only client
>>>in
>>>>>>my studio is me and I'm really just trying to get to a simpler workflow
>>>>>,for
>>>>>>the songwriting end of things, and still achieve quality results at
>the
>>>>>end
>>>>>>of the process.
>>>>>>
>>>>>>Can you eplain to me in a little more detail how you (and apparently
>>BT)
>>>>>>would be/are using Paris as the master summing mixer/recorder in this
>>>scenario?
>>>>>>
>>>>>>I've currently got Cubase SX3 lightpiped into Paris via a RME 9652
(
>>a
>>>>mini-Deej
>>>>>>set-up if, you will) but being a guy who only gets to work on my stuff
>>>>in
>>>>>>the evenings after work or on the weekends, the opportunity for confusion
>>>>>>in such a kludge ridden set-up doesn't lend itself to the creative
workflow.
>>>>>>That's why Cubase and a nice board/control surface appeals. My big
dilemma
>>>>>>though is that I still absolutely love the way Paris sounds.
>>>>>>
>>>>>>Anyway, thanks a ton for the input, greatly appreciated! I've got much
>>>>to
>>>>>>consider.
>>>>>>
>>>>>>Cheers,
>>>>>>jon
>>>>>>
>>>>>>
>>>>>>"LaMont" <jjdpro@ameritech.net> wrote:
>>>>>>>
>>>>>>>Hi Jon, I can chime in here on this question.
>>>>>>>
>>>>>>>I often work at a local studio http://www.lamourrecording.com/
>>>>>>>which has (2) Yamaha's DM2000. I can't speak highly enough of these
>>powerful
>>>>>>>beast.
>>>>>>>
>>>>>>>Great feel, 96 channels @ 96K
>>>>>>>Pro Tools, Neundo/Cubase/Sonar/Logic Controller
>>>>>>>Nice Comps/EQs on every channel
>>>>>>>(8) SPX-1000's DSP processors (REVerbs, Delays, Chorus.etc)
>>>>>>>Some of the sweetest (24) Mic pres you'll find
>>>>>>>All in a foot print that keeps the Engineer/Operator right in
>>>>>>>front of the mix..There's a ton more features..
>>>>>>>
>>>>>>>I had a chance (2years) ago to take the then Tascam 3200 for week
session
>>>>>>>spin. Due to the fact that no body in our area had a O2r/96, we
rented
>>>>>>>the tascam.. Man, to my ears and others, the Tascam delivers the goods.
>>>>>>I
>>>>>>>would have to say that the Tascam 3200 sonics was more "thick" than
>>the
>>>>>>DM2000.
>>>>>>>Different converters and clocks.. But, we mananged to get thru a sesion
>>>>>>without
>>>>>>>opening the manual!!
>>>>>>>You're not going to do that with the Yammys.. he 3200 had full eq
and
>>>>dynamics
>>>>>>>on every channel as well as I think 4 DSP processors for Verbs and
>dleays
>>>>>>>chorus FX.. The verbs were the star of this board. The algo's were
>from
>>>>>>TC!!
>>>>>>>the verb masters. Man, these verbs sounded like our TC 3000 ..really!!.
>>>>>>The
>>>>>>>Eqs were usuable as are the Comps/Lim..We click on the DAW controller
>>>>layer
>>>>>>>button, scrolled to the DAW template (Pro Tools)..Boom!! "Houston
We
>>>have
>>>>>>>Controll".. That easy.. We had transport, channel faders and Master
>>faders
>>>>>>>and edit scroll.. To be honest, we probable had more functions,but
>like
>>>>>>I
>>>>>>>stated earlier, we had not read the manual..
>>>>>>>Oh well.
>>>>>>>
>>>>>>>Like I told James, I'm looking seriously @ the DM4800 X2 for my Home
>>>studio..To
>>>>>>>host Both Nuendo & Pro Tools...AND yes, Liek BrianT does in Houston,
>>>Paris
>>>>>>>will be used a he master summing mixer/recorder..
>>>>>>>
>>>>>>>The DM3200/4800 can't be beat in their price range. They have the
sound,
>>>>>>>looks, and product maturity. Tascam knew they had a winner with the
>>DM24,then
>>>>>>>knocked the ball out of the park with the DM3200, and now DM 4800..
>>
>>>>>>>
>>>>>>>Now that it's official that Mackie has dropped the Ball with the DXB(20K
>>>>>>>Plus), now selling are drastic discounts. The DXB is a one sweet sounding
>>>>>>>board as well. At 9k it competes very well with Yammys O2r/96..But,
>>(2)
>>>>>>x
>>>>>>>DM4800 @ around is just as and (imo) more potent ..AND dropped in
a
>>cool
>>>>>>>Argosy, BAMM!..
>>>>>>>
>>>>>>>http://www.argosyconsole.com/dm3200.htm
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>"Jon Jiles" <nanaheyhey@no.com> wrote:
>>>>>>>>
>>>>>>>>Thanks for all the info James!
>>>>>>>>
>>>>>>>>How do they stack up against the Yamaha boards? (O2r96v2 and the
DM1000v2,etc)
>>>>>>>>Also, Cubase implementation will be a key factor if I move from Paris.
>>>>>>I
>>>>>>>>will consider the Yamaha boards too (used though due to price) because
>>>>>>of
>>>>>>>>the Yammy/Steinberg connection and better Cubase implementation I
>would
>>>>>>>suppose.
>>>>>>>>The Tascam boards do seem like a very good value though... especially
>>>>>if
>>>>>>>>they don't break and are not horribly non-intuitive.
>>>>>>>>
>>>>>>>>Thanks again,
>>>>>>>>Jon
>>>>>>>>
>>>>>>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>>>>>>
>>>>>>>>>By the way, the mic pres on the DM-32 and DM-48 are greatly improved
>>>>>and
>>>>>>>>vary
>>>>>>>>>usable. It was only the DM-24 that had the problems.
>>>>>>>>>
>>>>>>>>>James
>>>>>>>>>
>>>>>>>>>"James McCloskey" <excelsm@hotmail.com> wrote:
>>>>>>>>>>
>>>>>>>>>>Hey Jon!
>>>>>>>>>>
>>>>>>>>>>Some of the guys on the DA7 NG have switched to the Tascam DM 32s.
>>>>
>>>>>A
>>>>>>>customer
>>>>>>>>>>of mine also has one. The mixes from both source sound good.
You
>>>>should
>>>>>>>>>>always test drive before you buy. You have to like it. I would
>>think
>>>>>>>>twice
>>>>>>>>>>before buying a DM-24, the Mic pres were not so good, they had
low
>>>>head
>>>>>>>>>room.
>>>>>>>>>> If you use the DM-24 for line ins only, I think you'd be Ok.
There
>>>>>>was
>>>>>>>>>>an upgrade for the mic pres through Tascam, they may no longer
be
>>>doing
>>>>>>>>>that.
>>>>>>>>>>
>>>>>>>>>>I hear the DM manuals are terrible, you can go down load them.
>If
>>>>you
>>>>>>>>buy
>>>>>>>>>>one, make sure you have 30 full days to test it. Clear your planner
>>>>>>for
>>>>>>>>>>test time. Read the manual in advance and go to the NG a lot before
>>>>>>you
>>>>>>>>>>get it. Every once in awhile Tascam puts out a lemon, so you want
>>>>to
>>>>>>>be
>>>>>>>>>>able to fully test what you buy from them. Unless they have changed
>>>>>>their
>>>>>>>>>>policy, they only have a 90 day warranty!!!
>>>>>>>>>>
>>>>>>>>>>James
>>>>>>>>>>
>>>>>>>>>>"Jon Jiles" <snoid@sheboygan.com> wrote:
>>>>>>>>>>>
>>>>>>>>>>>Hi,
>>>>>>>>>>>
>>>>>>>>>>>Anyone here actually had any real hands on with this board/controller,
>>>>>>>>>especially
>>>>>>>>>>>with Cubase 4? James got me intrigued but I have read that the
>build
>>>>>>>quolity
>>>>>>>>>>>may be somewhat on cheesy side.
>>>>>>>>>>>
>>>>>>>>>>>Thanks,
>>>>>>>>>>>Jon
>>>>>>>>>>
>>>>>>>>>
>>>>>>>>
>>>>>>>
>>>>>>
>>>>>
>>>>
>>>
>>
>
|
|
|
|
Goto Forum:
Current Time: Wed Nov 27 23:36:30 PST 2024
Total time taken to generate the page: 0.07435 seconds
|
The PARIS Forums
Search
Help
Members
Register
Login
Home
