The PARIS Forums


Home » The PARIS Forums » PARIS: Main » Error Messages on PARIS (PARIS Software Problems)
Error Messages on PARIS [message #109860] Mon, 06 July 2020 20:56 Go to next message
raymack is currently offline  raymack   UNITED STATES
Messages: 11
Registered: January 2016
Location: Texas
Junior Member
Hello Fellow PARIS Users,

I have an older computer that was built back in 2003 for my PARIS 3.0 system that is running Windows XP. I started receiving an error message this week indicating that the "File overview was damaged and is being recalculated." This message appears in every project that I open and there are audio segments that consistently repeat that were not in the original recordings. I can't find anything online to help me with this issue. I have had a number of errors populating over the last several years from Windows XP; one of them is attached along with the error message from PARIS. My computer also locks up quite often, which forces me to reboot. Any ideas of what these problems could be and how I can resolve them? I'm also contemplating updating to Windows 7 or 10 if possible. Can anyone please let me know what I will need and where I can find the requirements? I saw Windows 7/8 drivers for $50.


Regards,
Ray
Re: Error Messages on PARIS [message #109861 is a reply to message #109860] Tue, 07 July 2020 18:57 Go to previous messageGo to next message
Rich.Kelley is currently offline  Rich.Kelley   UNITED STATES
Messages: 98
Registered: August 2009
Member
My guess is that your computer is dying. Sounds very similar to my situation with an old XP computer that kind of worked, but was super hard to get booted and PARIS loaded, and then would occasionally lock up.

I built a new system. Life is good now. I detailed the whole process here. Look for the thread from January of this year (2020).

If you're looking not to spend a bunch of money, I think you can spend a whole lot less than I did. You need another computer obviously. If the computer doesn't have PCI slots you'll need a solution for that. Then you'll need Mike Audet's 32/64 driver. If you're running Win 10 then you'll also want the ASIO driver too. I'm not sure if you need the ASIO for Win 7.

If you're running 3.0 with PACE then you have another problem. ID is not supporting PARIS anymore, so no response codes. Also PACE is not compatible with 64 bit operating systems. If you have a copy with the PACE problem fixed then no worries. PM me if you need more help on this issue.

Mike Audet is the guy who wrote the drivers and is THE tech resource on PARIS. You can buy the drivers on his website at ensoniq.ca.
Re: Error Messages on PARIS [message #109867 is a reply to message #109860] Sun, 30 August 2020 03:57 Go to previous messageGo to next message
Kim W. is currently offline  Kim W.   AUSTRALIA
Messages: 189
Registered: January 2010
Location: Australia
Senior Member
Sounds to me as if your hard disc has developed serious bad sector issues.
Cheers,
Kim
Re: Error Messages on PARIS [message #109889 is a reply to message #109861] Sun, 27 September 2020 10:54 Go to previous message
raymack is currently offline  raymack   UNITED STATES
Messages: 11
Registered: January 2016
Location: Texas
Junior Member
Hello Rich,

Thank you so much for your reply! I had a super busy month for August and September, but life is back to normal now and I'm back to working on my problems with my computer for PARIS. Sorry for the late reply.

I have a Win7 computer that I've been sitting on for a while so I plan to use this computer. I'm not familiar with PACE though. Is this required for my Win7 setup? Once I install that drivers, am I good after that? I'm going to purchase the drivers per the resource you suggested. Thanks!!


Ray
Previous Topic: PARIS Launch, RESTART, in Windows 10 Issue - Solution
Next Topic: File cache 439 offset debug
Goto Forum:
  


Current Time: Thu Dec 05 01:45:02 PST 2024

Total time taken to generate the page: 0.01275 seconds